|
Gonzalez-Iglesias, D., Esperante, D., Gimeno, B., Blanch, C., Fuster-Martinez, N., Martinez-Reviriego, P., et al. (2023). Analysis of the Multipactor Effect in an RF Electron Gun Photoinjector. IEEE Trans. Electron Devices, 70(1), 288–295.
Abstract: The objective of this work is the evaluation of the risk of suffering a multipactor discharge within an RF electron gun photoinjector. Photoinjectors are a type of source for intense electron beams, which are the main electron source for synchrotron light sources, such as free-electron lasers. The analyzed device consists of 1.6 cells and it has been designed to operate at the S-band. Besides, around the RF gun there is an emittance compensation solenoid, whose magnetic field prevents the growth of the electron beam emittance, and thus the degradation of the properties of the beam. The multipactor analysis is based on a set of numerical simulations by tracking the trajectories of the electron cloud in the cells of the device. To reach this aim, an in-house multipactor code was developed. Specifically, two different cases were explored: with the emittance compensation solenoid assumed to be off and with the emittance compensation solenoid in operation. For both the cases, multipactor simulations were carried out exploring different RF electric field amplitudes. Moreover, for a better understanding of the multipactor phenomenon, the resonant trajectories of the electrons and the growth rate of the electrons population are investigated.
|
|
|
Bayar, M., Ikeno, N., & Oset, E. (2020). Analysis of the psi (4040) and psi (4160) decay into D-(*()) (D)over-bar(()*()), D-s(()*()) (D)over-bar(s)(()*()). Eur. Phys. J. C, 80(3), 222–9pp.
Abstract: We have performed an analysis of the e+e--> D(*) data in the region of the psi(4040) and psi(4160) resonances which have a substantial overlap and require special care. By using the P-3(0) model to relate the different D(*)(D) over bar(*) production modes, we make predictions for production of these channels and compare with experiment and other theoretical approaches. As a side effect we find that these resonances qualify largely as c (c) over bar states and theweight of the meson-meson components in the wave function is very small.
|
|
|
Bach, E. et al, Bernabeu, J., Lacasta, C., Solaz, C., & Soldevila, U. (2024). Analysis of the quality assurance results from the initial part of production of the ATLAS18 ITK strip sensors. Nucl. Instrum. Methods Phys. Res. A, 1064, 169435–8pp.
Abstract: The production of strip sensors for the ATLAS Inner Tracker (ITk) started in 2021. Since then, a Quality Assurance (QA) program has been carried out continuously, by using specific test structures, in parallel to the Quality Control (QC) inspection of the sensors. The QA program consists of monitoring sensor-specific characteristics and the technological process variability, before and after the irradiation with gammas, neutrons, and protons. After two years, half of the full production volume has been reached and we present an analysis of the parameters measured as part of the QA process. The main devices used for QA purposes are miniature strip sensors, monitor diodes, and the ATLAS test chip, which contains several test structures. Such devices are tested by several sites across the collaboration depending on the type of samples (non-irradiated components or irradiated with protons, neutrons, or gammas). The parameters extracted from the tests are then uploaded to a database and analyzed by Python scripts. These parameters are mainly examined through histograms and timeevolution plots to obtain parameter distributions, production trends, and meaningful parameter-to-parameter correlations. The purpose of this analysis is to identify possible deviations in the fabrication or the sensor quality, changes in the behavior of the test equipment at different test sites, or possible variability in the irradiation processes. The conclusions extracted from the QA program have allowed test optimization, establishment of control limits for the parameters, and a better understanding of device properties and fabrication trends. In addition, any abnormal results prompt immediate feedback to a vendor.
|
|
|
Miyagawa, P. S. et al, Bernabeu, P., Lacasta, C., Solaz, C., & Soldevila, U. (2024). Analysis of the results from Quality Control tests performed on ATLAS18 Strip Sensors during on-going production. Nucl. Instrum. Methods Phys. Res. A, 1064, 169457–9pp.
Abstract: The ATLAS experiment will replace its existing Inner Detector with the new all -silicon Inner Tracker (ITk) to cope with the operating conditions of the forthcoming high -luminosity phase of the LHC (HL-LHC). The outer regions of the ITk will be instrumented with similar to 18000 ATLAS18 strip sensors fabricated by Hamamatsu Photonics K.K. (HPK). With the launch of full-scale sensor production in 2021, the ITk strip sensor community has undertaken quality control (QC) testing of these sensors to ensure compliance with mechanical and electrical specifications agreed with HPK. The testing is conducted at seven QC sites on each of the monthly deliveries of similar to 500 sensors. This contribution will give an overview of the QC procedures and analysis; the tests most likely to determine pass/fail for a sensor are IV, long-term leakage current stability, full strip test and visual inspection. The contribution will then present trends in the results and properties following completion of similar to 60% of production testing. It will also mention challenges overcome through collaborative efforts with HPK during the early phases of production. With less than 5% of sensors rejected by QC testing, the overall production quality has been very good.
|
|
|
Ramalho, M., Suhonen, J., Kostensalo, J., Alcala, G. A., Algora, A., Fallot, M., et al. (2022). Analysis of the total beta-electron spectrum of( 92)Rb: Implications for the reactor flux anomalies. Phys. Rev. C, 106(2), 024315–7pp.
Abstract: We present here a microscopic nuclear-structure calculation of a beta-electron spectrum including all the beta-decay branches of a high Q-value reactor fission product contributing significantly to the reactor antineutrino energy spectrum. We perform large-scale nuclear shell-model calculations of the total electron spectrum for the beta(-) decay of Rb-92 to states in Sr-92 using a computer cluster. We exploit the beta-branching data of a recent total absorption gamma-ray spectroscopy (TAGS) measurement to determine the effective values of the weak axial-vector coupling, g(A), and the weak axial charge, g(A)(gamma(5)). By using the TAGS data we avoid the bias stemming from the pandemonium effect which is a systematic error biasing the usual beta-decay measurements. We take fully into account all the involved allowed and forbidden beta transitions, in particular the first-forbidden nonunique ones which have earlier been shown to be relevant in the context of the reactor-antineutrino flux anomaly and the unexplained spectral shoulder, the “bump,” the former one having been interpreted as one of the strongest evidence for the existence of sterile neutrinos. Here we are able to present quantitative evidence for the relevance of forbidden nonunique beta(-) decays in a total beta spectrum of a fission product, in this case( 92)Rb, which is one of the major contributors to the total reactor antineutrino spectral shape. We demonstrate that taking the forbidden spectral shapes fully into consideration leads for Rb-92 to a 2.6%-4.6% reduction in the expected inverse beta-decay rate at the reactor antineutrino telescopes. We also confirm by our calculation of a total beta-electron spectrum that the forbidden transitions can contribute to the formation of the spectral bump in the reactor-antineutrino flux profile.
|
|
|
ATLAS Collaboration(Aaboud, M. et al), Alvarez Piqueras, D., Barranco Navarro, L., Cabrera Urban, S., Castillo Gimenez, V., Cerda Alberich, L., et al. (2017). Analysis of the Wtb vertex from the measurement of triple-differential angular decay rates of single top quarks produced in the t-channel at root s=8 TeV with the ATLAS detector. J. High Energy Phys., 12(12), 017–60pp.
Abstract: The electroweak production and subsequent decay of single top quarks in the t-channel is determined by the properties of the Wtb vertex, which can be described by the complex parameters of an effective Lagrangian. An analysis of a triple-differential decay rate in t-channel production is used to simultaneously determine five generalised helicity fractions and phases, as well as the polarisation of the produced top quark. The complex parameters are then constrained. This analysis is based on 20.2 fb(-1) of proton-proton collision data at a centre-of-mass energy of 8 TeV collected with the ATLAS detector at the LHC. The fraction of decays containing transversely polarised W bosons is measured to be f(1) = 0.30 +/- 0.05. The phase between amplitudes for transversely and longitudinally polarised W bosons recoiling against left-handed b-quarks is measured to be delta = 0.002 pi(+0.016 pi)(+0.017 pi), giving no indication of CP violation. The fractions of longitudinal or transverse W bosons accompanied by right-handed b-quarks are also constrained. Based on these measurements, limits are placed at 95% CL on the ratio of the complex coupling parameters Re [g(R)/V-L is an element of [-0.12, 0.17] and Im [g(R)/V-L is an element of [-0.07, 0.06]. Constraints are also placed on the ratios vertical bar V-R/V-L vertical bar and vertical bar g(L)/V-L vertical bar. In addition, the polarisation of single top quarks in the t-channel is constrained to be P > 0.72 (95% CL). None of the above measurements make assumptions about the value of any of the other parameters or couplings and all of them are in agreement with the Standard Model.
|
|
|
Gonzalez-Iglesias, D., Esperante, D., Gimeno, B., Boronat, M., Blanch, C., Fuster-Martinez, N., et al. (2021). Analytical RF Pulse Heating Analysis for High Gradient Accelerating Structures. IEEE Trans. Nucl. Sci., 68(2), 78–91.
Abstract: The main aim of this work is to present a simple method, based on analytical expressions, for obtaining the temperature increase due to the Joule effect inside the metallic walls of an RF accelerating component. This technique relies on solving the 1-D heat-transfer equation for a thick wall, considering that the heat sources inside the wall are the ohmic losses produced by the RF electromagnetic fields penetrating the metal with finite electrical conductivity. Furthermore, it is discussed how the theoretical expressions of this method can be applied to obtain an approximation to the temperature increase in realistic 3-D RF accelerating structures, taking as an example the cavity of an RF electron photoinjector and a traveling wave linac cavity. These theoretical results have been benchmarked with numerical simulations carried out with commercial finite-element method (FEM) software, finding good agreement among them. Besides, the advantage of the analytical method with respect to the numerical simulations is evidenced. In particular, the model could be very useful during the design and optimization phase of RF accelerating structures, where many different combinations of parameters must be analyzed in order to obtain the proper working point of the device, allowing to save time and speed up the process. However, it must be mentioned that the method described in this article is intended to provide a quick approximation to the temperature increase in the device, which of course is not as accurate as the proper 3-D numerical simulations of the component.
|
|
|
Caron, S., Gomez-Vargas, G. A., Hendriks, L., & Ruiz de Austri, R. (2018). Analyzing gamma rays of the Galactic Center with deep learning. J. Cosmol. Astropart. Phys., 05(5), 058–24pp.
Abstract: We present the application of convolutional neural networks to a particular problem in gamma ray astronomy. Explicitly, we use this method to investigate the origin of an excess emission of GeV gamma rays in the direction of the Galactic Center, reported by several groups by analyzing Fermi-LAT data. Interpretations of this excess include gamma rays created by the annihilation of dark matter particles and gamma rays originating from a collection of unresolved point sources, such as millisecond pulsars. We train and test convolutional neural networks with simulated Fermi-LAT images based on point and diffuse emission models of the Galactic Center tuned to measured gamma ray data. Our new method allows precise measurements of the contribution and properties of an unresolved population of gamma ray point sources in the interstellar diffuse emission model. The current model predicts the fraction of unresolved point sources with an error of up to 10% and this is expected to decrease with future work.
|
|
|
ATLAS Collaboration(Aaboud, M. et al), Alvarez Piqueras, D., Barranco Navarro, L., Cabrera Urban, S., Castillo Gimenez, V., Cerda Alberich, L., et al. (2018). Angular analysis of B-d(0) -> K* mu(+)mu(-) decays in pp collisions at root s=8 TeV with the ATLAS detector. J. High Energy Phys., 10(10), 047–47pp.
Abstract: An angular analysis of the decay B-d(0) -> K*mu(+)mu(-) is presented, based on proton-proton collision data recorded by the ATLAS experiment at the LHC. The study is using 20.3 fb(-1) of integrated luminosity collected during 2012 at centre-of-mass energy of root s = 8TeV. Measurements of the K* longitudinal polarisation fraction and a set of angular parameters obtained for this decay are presented. The results are compatible with the Standard Model predictions.
|
|
|
LHCb Collaboration(Aaij, R. et al), Henry, L., Jashal, B. K., Martinez-Vidal, F., Oyanguren, A., Remon Alepuz, C., et al. (2021). Angular analysis of B0 -> D*- D*s+ with D*s+ -> Ds + gamma decays. J. High Energy Phys., 06(6), 177–30pp.
Abstract: The first full angular analysis of the B0 -> D-Ds+ decay is performed using 6 fb(-1) of pp collision data collected with the LHCb experiment at a centre-of-mass energy of 13 TeV. The Ds+-> Ds+gamma and D*- -> D<overbar></mml:mover>0- vector meson decays are used with the subsequent Ds+ -> K+K-pi (+) and D<overbar></mml:mover>0 -> K+pi (-) decays. All helicity amplitudes and phases are measured, and the longitudinal polarisation fraction is determined to be f(L) = 0.578 +/- 0.010 +/- 0.011 with world-best precision, where the first uncertainty is statistical and the second is systematic. The pattern of helicity amplitude magnitudes is found to align with expectations from quark-helicity conservation in B decays. The ratio of branching fractions [B(B0 -> D-Ds+) x B(Ds+-> Ds+gamma)]/B(B-0 -> D(*-)Ds+) is measured to be 2.045 +/- 0.022 +/- 0.071 with world-best precision. In addition, the first observation of the Cabibbo-suppressed B-s -> D(*-)Ds+ decay is made with a significance of seven standard deviations. The branching fraction ratio B(B-s -> D(*-)Ds<mml:mo>+)/B(B-0 -> D(*-)Ds<mml:mo>+) is measured to be 0.049 +/- 0.006 +/- 0.003 +/- 0.002, where the third uncertainty is due to limited knowledge of the ratio of fragmentation fractions.<fig id=“Figa” position=“anchor”><graphic position=“anchor” specific-use=“HTML” mime-subtype=“JPEG” xmlns:xlink=“http://www.w3.org/1999/xlink” xlink:href=“MediaObjects/13130202116089FigaHTML.jpg” id=“MO1”></graphic
|
|