Pavao, R. P., Sakai, S., & Oset, E. (2017). Triangle singularities in B- -> D*(0)pi(-)pi(0)eta and B- -> D*(0)pi(-)pi(+)pi(-). Eur. Phys. J. C, 77(9), 599–8pp.
Abstract: The possible role of the triangle mechanism in the B- decay into D*(0)pi(-)pi(0)eta and D*(0)pi(-)pi(+)pi(-) is investigated. In this process, the triangle singularity appears from the decay of B- into D*K-0(-) K*(0) followed by the decay of K-*0 into pi(-) K+ and the fusion of the K+ K-, which forms the a(0)(980) or f(0)(980), which finally decay into pi(0)eta or pi(+)pi(-), respectively. The triangle mechanism from the (K) over bar * K (K) over bar loop generates a peak around 1420 MeV in the invariant mass of pi(-) a(0) or pi(-) f(0), and it gives sizable branching fractions, Br(B- -> D*(0)pi(-) a(0); a(0) -> pi(0)eta) = (1.66 +/- 0.45) x 10(-6) and Br(B- -> D*(0)pi(-) f(0); f(0) -> pi(+)pi(-)) = (2.82 +/- 0.75) x 10(-6).
|
Marco-Hernandez, R., Bau, M., Ferrari, M., Ferrari, V., Pedersen, F., & Soby, L. (2017). A Low-Noise Charge Amplifier for the ELENA Trajectory, Orbit, and Intensity Measurement System. IEEE Trans. Nucl. Sci., 64(9), 2465–2473.
Abstract: A low-noise head amplifier has been developed for the extra low energy antiproton ring beam trajectory, orbit, and intensity measurement system at CERN. This system is based on 24 double-electrode electrostatic beam position monitors installed around the ring. A head amplifier is placed close to each beam position monitor to amplify the electrode signals and generate a difference and a sum signal. These signals are sent to the digital acquisition system, about 50 m away from the ring, where they are digitized and further processed. The beam position can be measured by dividing the difference signal by the sum signal while the sum signal gives information relative to the beam intensity. The head amplifier consists of two discrete charge preamplifiers with junction field effect transistor (JFET) inputs, a sum and a difference stage, and two cable drivers. Special attention has been paid to the amplifier printed circuit board design to minimize the parasitic capacitances and inductances at the charge amplifier stages to meet the gain and noise requirements. The measurements carried out on the head amplifier showed a gain of 40.5 and 46.5 dB for the sum and difference outputs with a bandwidth from 200 Hz to 75 MHz and an input voltage noise density lower than 400 pV/v Hz. Twenty head amplifiers have been already installed in the ring and they have been used to detect the first beam signals during the first commissioning stage in November 2016.
|
LHCb Collaboration(Aaij, R. et al), Garcia Martin, L. M., Henry, L., Martinez-Vidal, F., Oyanguren, A., Remon Alepuz, C., et al. (2017). Measurement of B-s(0) and D-s(-) Meson Lifetimes. Phys. Rev. Lett., 119(10), 101801–10pp.
Abstract: We report on a measurement of the flavor-specific B-s(0) lifetime and of the D-s(-) lifetime using proton-proton collisions at center-of-mass energies of 7 and 8 TeV, collected by the LHCb experiment and corresponding to 3.0 fb(-1) of integrated luminosity. Approximately 407 000 B-s(0) -> D-s(()*()) -> D-s(()*()-) mu+v(mu) decays are partially reconstructed in the K+K-pi(-)mu(+) final state. The B-s(0) and D-s(-) natural widths are determined using, as a reference, kinematically similar B-0 -> Dd(*)(-) mu+v(mu) decays reconstructed in the same final state. The resulting differences between widths of B-s(0) and B-0 mesons and of D-s(-) and D- mesons are Delta(Gamma)(B) = -0.0115 +/- 0.0053(stat) +/- 0.0041 (syst) ps(-1) and Delta(Gamma)(D) = 1.0131 +/- 0.0117(stat) +/- 0.0065(syst) ps(-1), respectively. Combined with the known B-0 and D- lifetimes, these yield the flavor-specific B-s(0) lifetime, tau(fs)(Bs0) = 1.547 +/- 0.013 (stat) +/- 0.010 (syst) +/- 0.004(tau(B)) ps and the D-s(-) lifetime, tau(Ds-) = 0.5064 +/- 0.0030(stat) +/- 0.0017(syst) +/- 0.0017(sys) +/- 0.0017(tau(D)). The last uncertainties originate from the limited knowledge of the B-0 and D- lifetimes. The results improve upon current determinations.
|
Liang, W. H., Bayar, M., & Oset, E. (2017). Lambda(b) -> pi(-)(D-S(-)) Lambda(C)(2595), pi(-)(D-S(-)) Lambda(C)(2625) decays and DN, D*N molecular components. Eur. Phys. J. C, 77(1), 39–9pp.
Abstract: From the perspective that Lambda(C)(2595) and Lambda(C)(2625) are dynamically generated resonances from the DN, D*N interaction and coupled channels, we have evaluated the rates for Lambda(b) -> pi(-)Lambda(C)(2595) and Lambda(b) -> pi(-)Lambda(C)(2625) up to a global unknown factor that allows us to calculate the ratio of rates and compare with experiment, where good agreement is found. Similarly, we can also make predictions for the ratio of rates of the, yet unknown, decays of Lambda(b) -> D-s(-)Lambda(C)(2595) and Lambda(b) -> D-s(-)Lambda(c)(2625) and make estimates for their individual branching fractions.
|
Aliaga, R. J. (2017). Real-Time Estimation of Zero Crossings of Sampled Signals for Timing Using Cubic Spline Interpolation. IEEE Trans. Nucl. Sci., 64(8), 2414–2422.
Abstract: A scheme is proposed for hardware estimation of the location of zero crossings of sampled signals with subsample resolution for timing applications, which consists of interpolating the signal with a cubic spline near the zero crossing and then finding the root of the resulting polynomial. An iterative algorithm based on the bisection method is presented that obtains one bit of the result per step and admits an efficient digital implementation using fixed-point representation. In particular, the root estimation iteration involves only two additions, and the initial values can be obtained from finite impulse response (FIR) filters with certain symmetry properties. It is shown that this allows online real-time estimation of timestamps in free-running sampling detector systems with improved accuracy with respect to the more common linear interpolation. The method is evaluated with simulations using ideal and real timing signals, and estimates are given for the resource usage and speed of its implementation.
|
