| Records |
| Author |
Miyagawa, P.S. et al; Bernabeu, P.; Lacasta, C.; Solaz, C.; Soldevila, U. |
| Title |
Analysis of the results from Quality Control tests performed on ATLAS18 Strip Sensors during on-going production |
Type |
Journal Article |
| Year |
2024 |
Publication |
Nuclear Instruments & Methods in Physics Research A |
Abbreviated Journal |
Nucl. Instrum. Methods Phys. Res. A |
Volume  |
1064 |
Issue |
|
Pages |
169457 - 9pp |
| Keywords |
HL-LHC; ATLAS; ITk; Strip sensors |
| Abstract |
The ATLAS experiment will replace its existing Inner Detector with the new all -silicon Inner Tracker (ITk) to cope with the operating conditions of the forthcoming high -luminosity phase of the LHC (HL-LHC). The outer regions of the ITk will be instrumented with similar to 18000 ATLAS18 strip sensors fabricated by Hamamatsu Photonics K.K. (HPK). With the launch of full-scale sensor production in 2021, the ITk strip sensor community has undertaken quality control (QC) testing of these sensors to ensure compliance with mechanical and electrical specifications agreed with HPK. The testing is conducted at seven QC sites on each of the monthly deliveries of similar to 500 sensors. This contribution will give an overview of the QC procedures and analysis; the tests most likely to determine pass/fail for a sensor are IV, long-term leakage current stability, full strip test and visual inspection. The contribution will then present trends in the results and properties following completion of similar to 60% of production testing. It will also mention challenges overcome through collaborative efforts with HPK during the early phases of production. With less than 5% of sensors rejected by QC testing, the overall production quality has been very good. |
| Address |
[Miyagawa, P. S.; Beck, G. A.; Bevan, A. J.; Chen, Z.; Dawson, I.; Zenz, S. C.] Queen Mary Univ London, Particle Phys Res Ctr, GO Jones Bldg, Mile End Rd, London E14NS, England, Email: paul.miyagawa@cern.ch |
| Corporate Author |
|
Thesis |
|
| Publisher |
Elsevier |
Place of Publication |
|
Editor |
|
| Language |
English |
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0168-9002 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
WOS:001249611300001 |
Approved |
no |
| Is ISI |
yes |
International Collaboration |
yes |
| Call Number |
IFIC @ pastor @ |
Serial |
6158 |
| Permanent link to this record |
| |
|
| |
| Author |
Latonova, V. et al; Bernabeu, J.; Lacasta, C.; Solaz, C.; Soldevila, U. |
| Title |
Characterization of the polysilicon resistor in silicon strip sensors for ATLAS inner tracker as a function of temperature, pre- and post-irradiation |
Type |
Journal Article |
| Year |
2023 |
Publication |
Nuclear Instruments & Methods in Physics Research A |
Abbreviated Journal |
Nucl. Instrum. Methods Phys. Res. A |
| Volume |
1050 |
Issue |
|
Pages |
168119 - 5pp |
| Keywords |
HL-LHC; ATLAS ITk; Silicon micro-strip sensor; Polysilicon bias resistor; Testchip |
| Abstract |
The high luminosity upgrade of the Large Hadron Collider, foreseen for 2029, requires the replacement of the ATLAS Inner Detector with a new all-silicon Inner Tracker (ITk). The expected ultimate total integrated luminosity of 4000 fb(-1) means that the strip part of the ITk detector will be exposed to the total particle fluences and ionizing doses reaching the values of 1.6 center dot 10(15) MeVn(eq)/cm(2) and 0.66MGy, respectively, including a safety factor of 1.5. Radiation hard n(+)-in-p micro-strip sensors were developed by the ATLAS ITk strip collaboration and are produced by Hamamatsu Photonics K.K. The active area of each ITk strip sensor is delimited by the n-implant bias ring, which is connected to each individual n(+) implant strip by a polysilicon bias resistor. The total resistance of the polysilicon bias resistor should be within a specified range to keep all the strips at the same potential, prevent the signal discharge through the grounded bias ring and avoid the readout noise increase. While the polysilicon is a ubiquitous semiconductor material, the fluence and temperature dependence of its resistance is not easily predictable, especially for the tracking detector with the operational temperature significantly below the values typical for commercial microelectronics. Dependence of the resistance of polysilicon bias resistor on the temperature, as well as on the total delivered fluence and ionizing dose, was studied on the specially-designed test structures called ATLAS Testchips, both before and after their irradiation by protons, neutrons, and gammas to the maximal expected fluence and ionizing dose. The resistance has an atypical negative temperature dependence. It is different from silicon, which shows that the grain boundary has a significant contribution to the resistance. We discuss the contributions by parameterizing the activation energy of the polysilicon resistance as a function of the temperature for unirradiated and irradiated ATLAS Testchips. |
| Address |
[Latonova, V.; Federicova, P.; Kroll, J.; Kvasnicka, J.; Mikestikova, M.] Acad Sci Czech Republ, Inst Phys, Slovance 2, Prague 8, Czech Republic, Email: vera.latonova@cern.ch |
| Corporate Author |
|
Thesis |
|
| Publisher |
Elsevier |
Place of Publication |
|
Editor |
|
| Language |
English |
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0168-9002 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
WOS:001035405300001 |
Approved |
no |
| Is ISI |
yes |
International Collaboration |
yes |
| Call Number |
IFIC @ pastor @ |
Serial |
5601 |
| Permanent link to this record |
| |
|
| |
| Author |
Cervello, A.; Carrio, F.; Garcia, R.; Martos, J.; Soret, J.; Torres, J.; Valero, A. |
| Title |
The TileCal PreProcessor interface with the ATLAS global data acquisition system at the HL-LHC |
Type |
Journal Article |
| Year |
2022 |
Publication |
Nuclear Instruments & Methods in Physics Research A |
Abbreviated Journal |
Nucl. Instrum. Methods Phys. Res. A |
| Volume |
1043 |
Issue |
|
Pages |
167492 - 2pp |
| Keywords |
ATLAS; Tile Calorimeter; HL-LHC; TilePPr; FELIX; SWROD; DAQ |
| Abstract |
The Large Hadron Collider (LHC) has envisaged a series of upgrades towards a High Luminosity LHC (HL-LHC) delivering five times the LHC nominal instantaneous luminosity. It will take place throughout 2026-2028, corresponding to the Long Shutdown 3. During this upgrade, the ATLAS Tile Hadronic Calorimeter (TileCal) will replace completely on-and off-detector electronics adopting a new read-out architecture. Signals captured from TileCal are digitized by the on-detector electronics and transmitted to the TileCal PreProcessor (TilePPr) located off-detector, which provides the interface with the ATLAS trigger and data acquisition systems.TilePPr receives, process and transmits the data from the on-detector system and transmits it to the Front -End Link eXchange (FELIX) system. FELIX is the ATLAS common hardware in all the subdetectors designed to act as a data router, receiving and forwarding data to the SoftWare Read-Out Driver (SWROD) computers. FELIX also distributes the Timing, Trigger and Control (TTC) signals to the TilePPr to be propagated to the on-detector electronics. The SWROD is an ATLAS common software solution to perform detector specific data processing, including configuration, calibration, control and monitoring of the partitionIn this contribution we will introduce the new read-out elements for TileCal at the HL-LHC, the intercon-nection between the off-detector electronics and the FELIX system, the configuration and implementation for the test beam campaigns, as well as future developments of the preprocessing and monitoring status of the calorimeter modules through the SWROD infrastructure. |
| Address |
[Cervello, Antonio; Carrio, Fernando; Valero, Alberto] UV, CSIC, Inst Fis Corpuscular, Carrer Catedrat Jose Beltran Martinez 2, Valencia 46980, Spain, Email: antonio.cervello@uv.es |
| Corporate Author |
|
Thesis |
|
| Publisher |
Elsevier |
Place of Publication |
|
Editor |
|
| Language |
English |
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0168-9002 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
WOS:000868495700012 |
Approved |
no |
| Is ISI |
yes |
International Collaboration |
no |
| Call Number |
IFIC @ pastor @ |
Serial |
5399 |
| Permanent link to this record |
| |
|
| |
| Author |
Hara, K. et al; Escobar, C.; Garcia, C.; Lacasta, C.; Miñano, M.; Soldevila, U. |
| Title |
Charge collection study with the ATLAS ITk prototype silicon strip sensors ATLAS17LS |
Type |
Journal Article |
| Year |
2020 |
Publication |
Nuclear Instruments & Methods in Physics Research A |
Abbreviated Journal |
Nucl. Instrum. Methods Phys. Res. A |
| Volume |
983 |
Issue |
|
Pages |
164422 - 6pp |
| Keywords |
ATLAS ITk; Microstrip sensor; Charge collection; Radiation damage |
| Abstract |
The inner tracker of the ATLAS detector is scheduled to be replaced by a completely new silicon-based inner tracker (ITk) for the Phase-II of the CERN LHC (HL-LHC). The silicon strip detector covers the volume 40 < R < 100 cm in the radial and vertical bar z vertical bar <300 cm in the longitudinal directions. The silicon sensors for the detector will be fabricated using the n(+)-on-p 6-inch wafer technology, for a total of 22,000 wafers. Intensive studies were carried out on the final prototype sensors ATLAS17LS fabricated by Hamamatsu Photonics (HPK). The charge collection properties were examined using penetrating Sr-90 beta-rays and the ALIBAVA fast readout system for the miniature sensors of 1 cm xl cm in area. The samples were irradiated by protons in the 27 MeV Birmingham Cyclotron, the 70 MeV CYRIC at Tohoku University, and the 24 GeV CERN-PS, and by neutrons at Ljubljana TAIGA reactor for fluence values up to 2 x 10(15) n(eq)/cm(2). The change in the charge collection with fluence was found to be similar to the previous prototype ATLAS12, and acceptable for the ITk. Sensors with two active thicknesses, 300 μm (standard) and 240 μm (thin), were compared and the difference in the charge collection was observed to be small for bias voltages up to 500 V. Some samples were also irradiated with gamma radiation up to 2 MGy, and the full depletion voltage was found to decrease with the dose. This was caused by the Compton electrons due to the( 60)Co gamma radiation. To summarize, the design of the ATLAS17LS and technology for its fabrication have been verified for implementation in the ITk. We are in the stage of sensor pre-production with the first sensors already delivered in January of 2020. |
| Address |
[Hara, K.] Univ Tsukuba, Inst Pure & Appl Sci, Tsukuba, Ibaraki 3058571, Japan, Email: hara@hep.px.tsukuba.ac.jp |
| Corporate Author |
|
Thesis |
|
| Publisher |
Elsevier |
Place of Publication |
|
Editor |
|
| Language |
English |
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0168-9002 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
WOS:000581808300002 |
Approved |
no |
| Is ISI |
yes |
International Collaboration |
yes |
| Call Number |
IFIC @ pastor @ |
Serial |
4606 |
| Permanent link to this record |
| |
|
| |
| Author |
Fernandez-Tejero, J.; Bartl, U.; Docke, M.; Fadeyev, V.; Fleta, C.; Hacker, J.; Hommels, B.; Lacasta, C.; Parzefall, U.; Soldevila, U.; Stocker, G.; Ullan, M.; Unno, Y. |
| Title |
Design and evaluation of large area strip sensor prototypes for the ATLAS Inner Tracker detector |
Type |
Journal Article |
| Year |
2020 |
Publication |
Nuclear Instruments & Methods in Physics Research A |
Abbreviated Journal |
Nucl. Instrum. Methods Phys. Res. A |
| Volume |
981 |
Issue |
|
Pages |
164536 - 6pp |
| Keywords |
ATLAS; Silicon strip sensors; Large area silicon sensors; Layout design; Prototype evaluation; Market survey |
| Abstract |
The ATLAS community is facing the last stages prior to the production of the upgraded silicon strip Inner Tracker for the High-Luminosity Large Hadron Collider. An extensive Market Survey was carried out in order to evaluate the capability of different foundries to fabricate large area silicon strip sensors, satisfying the ATLAS specifications. The semiconductor manufacturing company, Infineon Technologies AG, was one of the two foundries, along with Hamamatsu Photonics K.K., that reached the last stage of the evaluation for the production of the new devices. The full prototype wafer layout for the participation of Infineon, called ATLAS17LS-IFX, was designed using a newly developed Python-based Automatic Layout Generation Tool, able to rapidly design sensors with different characteristics and dimensions based on a few geometrical and technological input parameters. This work presents the layout design process and the results obtained from the evaluation of the new Infineon large area sensors before and after proton and neutron irradiations, up to fluences expected in the inner layers of the future ATLAS detector. |
| Address |
[Fernandez-Tejero, J.; Fleta, C.; Ullan, M.] CSIC, Ctr Nacl Microelect IMB CNM, Campus UAB Bellaterra, Barcelona 08193, Spain, Email: Xavi.Fdez@cern.ch |
| Corporate Author |
|
Thesis |
|
| Publisher |
Elsevier |
Place of Publication |
|
Editor |
|
| Language |
English |
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0168-9002 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
WOS:000581799800023 |
Approved |
no |
| Is ISI |
yes |
International Collaboration |
yes |
| Call Number |
IFIC @ pastor @ |
Serial |
4579 |
| Permanent link to this record |
| |
|
| |
| Author |
Ruhr, F. et al; Escobar, C.; Miñano, M. |
| Title |
Testbeam studies of barrel and end-cap modules for the ATLAS ITk strip detector before and after irradiation |
Type |
Journal Article |
| Year |
2020 |
Publication |
Nuclear Instruments & Methods in Physics Research A |
Abbreviated Journal |
Nucl. Instrum. Methods Phys. Res. A |
| Volume |
979 |
Issue |
|
Pages |
164430 - 6pp |
| Keywords |
Particle physics; Tracking detectors; ATLAS; HL-LHC; Test beam |
| Abstract |
In order to cope with the occupancy and radiation doses expected at the High-Luminosity LHC, the ATLAS experiment will replace its Inner Detector with an all-silicon Inner Tracker (ITk), consisting of pixel and strip subsystems. In the last two years, several prototype ITk strip modules have been tested using beams of high energy electrons produced at the DESY-II testbeam facility. Tracking was provided by EUDET telescopes. The modules tested are built from two sensor types: the rectangular ATLAS17LS, which will be used in the outer layers of the central barrel region of the detector, and the annular ATLAS12EC, which will be used in the innermost ring (R0) of the forward region. Additionally, a structure with two RO modules positioned back-to-back has been measured, demonstrating space point reconstruction using the stereo angle of the strips. Finally, one barrel and one RO module have been measured after irradiation to 40% beyond the expected end-of-lifetime fluence. The data obtained allow for thorough tests of the module performance, including charge collection, noise occupancy, detection efficiency, and tracking performance. The results give confidence that the ITk strip detector will meet the requirements of the ATLAS experiment. |
| Address |
[Ruehr, F.; Argos, C. Garcia; Hauser, M.; Moos, F.; Rodriguez, A. Rodriguez; Sperlich, D.; Wiik-Fuchs, L.] Albert Ludwigs Univ Freiburg, Phys Inst, Freiburg, Germany, Email: frederik.ruehr@cern.ch |
| Corporate Author |
|
Thesis |
|
| Publisher |
Elsevier |
Place of Publication |
|
Editor |
|
| Language |
English |
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0168-9002 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
WOS:000573295200013 |
Approved |
no |
| Is ISI |
yes |
International Collaboration |
yes |
| Call Number |
IFIC @ pastor @ |
Serial |
4548 |
| Permanent link to this record |
| |
|
| |
| Author |
Benitez, V. et al; Bernabeu, J.; Garcia, C.; Lacasta, C.; Marco, R.; Rodriguez, D.; Santoyo, D.; Solaz, C.; Soldevila, U. |
| Title |
Sensors for the End-cap prototype of the Inner Tracker in the ATLAS Detector Upgrade |
Type |
Journal Article |
| Year |
2016 |
Publication |
Nuclear Instruments & Methods in Physics Research A |
Abbreviated Journal |
Nucl. Instrum. Methods Phys. Res. A |
| Volume |
833 |
Issue |
|
Pages |
226-232 |
| Keywords |
Silicon radiation detectors; Strip sensors; HL-LHC; ATLAS Upgrade; Inner Tracker (ITk); End-cap |
| Abstract |
The new silicon microstrip sensors of the End-cap part of the HL-LHC ATLAS Inner Tracker (ITk) present a number of challenges due to their complex design features such as the multiple different sensor shapes, the varying strip pitch, or the built-In stereo angle. In order to investigate these specific problems, the “petalet” prototype was defined as a small End-cap prototype. The sensors for the petalet prototype include several new layout and technological solutions to investigate the issues, they have been tested in detail by the collaboration. The sensor description and detailed test results are presented in this paper. New software tools have been developed for the automatic layout generation of the complex designs. The sensors have been fabricated, characterized and delivered to the institutes in the collaboration for their assembly on petalet prototypes. This paper describes the lessons learnt from the design and tests of the new solutions implemented on these sensors, which are being used for the full petal sensor development. This has resulted in the ITIc strip, community acquiring the necessary expertise to develop the full End-cap structure, the petal. |
| Address |
[Benitez, V.; Ullan, M.; Quirion, D.; Pellegrini, G.; Fleta, C.; Lozano, M.] CSIC, CNM, IMB, Campus Univ Bellaterra, Barcelona 08193, Spain, Email: miguel.ullan@imb-cnm.csic.es |
| Corporate Author |
|
Thesis |
|
| Publisher |
Elsevier Science Bv |
Place of Publication |
|
Editor |
|
| Language |
English |
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0168-9002 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
WOS:000383818200032 |
Approved |
no |
| Is ISI |
yes |
International Collaboration |
yes |
| Call Number |
IFIC @ pastor @ |
Serial |
2816 |
| Permanent link to this record |
| |
|
| |
| Author |
Ullan, M.; Benitez, V.; Quirion, D.; Zabala, M.; Pellegrini, G.; Lozano, M.; Lacasta, C.; Soldevila, U.; Garcia, C.; Fadeyev, V.; Wortman, J.; DeFilippis, J.; Shumko, M.; Grillo, A.A.; Sadrozinski, H.F.W. |
| Title |
Low-resistance strip sensors for beam-loss event protection |
Type |
Journal Article |
| Year |
2014 |
Publication |
Nuclear Instruments & Methods in Physics Research A |
Abbreviated Journal |
Nucl. Instrum. Methods Phys. Res. A |
| Volume |
765 |
Issue |
|
Pages |
252-257 |
| Keywords |
Silicon radiation detectors; Strip sensors; Punch through protection; Beam loss; HL-LHC; ATLAS Upgrade |
| Abstract |
AC coupled silicon strip sensors can be damaged in case of a beam loss due to the possibility of a large charge accumulation in the bulk, developing very high voltages across the coupling capacitors which can destroy them. Punch-through structures are currently used to avoid this problem helping to evacuate the accumulated charge as large voltages are developing. Nevertheless, previous experiments, performed with laser pulses, have shown that these structures can become ineffective in relatively long strips. The large value of the implant resistance can effectively isolate the “far” end of the strip from the punchthrough structure leading to large voltages. We present here our developments to fabricate lowresistance strip sensors to avoid this problem. The deposition of a conducting material in contact with the implants drastically reduces the strip resistance, assuring the effectiveness of the punch-through structures. First devices have been fabricated with this new technology. Initial results with laser tests show the expected reduction in peak voltages on the low resistivity implants. Other aspects of the sensor performance, including the signal formation, are not affected by the new technology. |
| Address |
[Ullan, M.; Benitez, V.; Quirion, D.; Zabala, M.; Pellegrini, G.; Lozano, M.] CSIC, Ctr Nacl Microelect IMB CNM, Barcelona 08193, Spain, Email: Miguel.Ullan@imb-cnm.csic.es |
| Corporate Author |
|
Thesis |
|
| Publisher |
Elsevier Science Bv |
Place of Publication |
|
Editor |
|
| Language |
English |
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0168-9002 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
WOS:000344621000048 |
Approved |
no |
| Is ISI |
yes |
International Collaboration |
yes |
| Call Number |
IFIC @ pastor @ |
Serial |
2003 |
| Permanent link to this record |
| |
|
| |
| Author |
ATLAS Collaboration (Aad, G. et al); Cabrera Urban, S.; Castillo Gimenez, V.; Costa, M.J.; Fernandez Martinez, P.; Ferrer, A.; Fiorini, L.; Fuster, J.; Garcia, C.; Garcia Navarro, J.E.; Gonzalez de la Hoz, S.; Hernandez Jimenez, Y.; Higon-Rodriguez, E.; Irles Quiles, A.; Jimenez Pena, J.; Kaci, M.; King, M.; Lacasta, C.; Lacuesta, V.R.; Marti-Garcia, S.; Mitsou, V.A.; Moles-Valls, R.; Oliver Garcia, E.; Pedraza Lopez, S.; Perez Garcia-Estañ, M.T.; Romero Adam, E.; Ros, E.; Salt, J.; Sanchez Martinez, V.; Soldevila, U.; Sanchez, J.; Torro Pastor, E.; Valero, A.; Valladolid Gallego, E.; Valls Ferrer, J.A.; Vos, M. |
| Title |
Search for a CP-odd Higgs boson decaying to Zh in pp collisions at root s=8 TeV with the ATLAS detector |
Type |
Journal Article |
| Year |
2015 |
Publication |
Physics Letters B |
Abbreviated Journal |
Phys. Lett. B |
| Volume |
744 |
Issue |
|
Pages |
163-183 |
| Keywords |
BSM Higgs boson; ATLAS |
| Abstract |
A search for a heavy, CP-odd Higgs boson, A, decaying into a Z boson and a 125 GeV Higgs boson, h, with the ATLAS detector at the LHC is presented. The search uses proton-proton collision data at a centre-of-mass energy of 8 TeV corresponding to an integrated luminosity of 20.3 fb(-1). Decays of CP-even h bosons to tau tau or bb pairs with the Z boson decaying to electron or muon pairs are considered, as well as h -> bb decays with the Z boson decaying to neutrinos. No evidence for the production of an A boson in these channels is found and the 95% confidence level upper limits derived for sigma(gg -> A) x BR(A -> Zh) x BR(h -> f (f) over bar) are 0.098-0.013 pb for f = tau and 0.57-0.014 pb for f = b in a range of m(A) = 220-1000 GeV. The results are combined and interpreted in the context of two-Higgs-doublet models. |
| Address |
[Jackson, P.; Lee, L.; Soni, N.; White, M. J.] Univ Adelaide, Dept Phys, Adelaide, SA, Australia |
| Corporate Author |
|
Thesis |
|
| Publisher |
Elsevier Science Bv |
Place of Publication |
|
Editor |
|
| Language |
English |
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0370-2693 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
WOS:000353892000030 |
Approved |
no |
| Is ISI |
yes |
International Collaboration |
yes |
| Call Number |
IFIC @ pastor @ |
Serial |
2225 |
| Permanent link to this record |
| |
|
| |
| Author |
ATLAS Collaboration (Aad, G. et al); Cabrera Urban, S.; Castillo Gimenez, V.; Costa, M.J.; Ferrer, A.; Fiorini, L.; Fuster, J.; Garcia, C.; Garcia Navarro, J.E.; Gonzalez de la Hoz, S.; Hernandez Jimenez, Y.; Higon-Rodriguez, E.; Irles Quiles, A.; Kaci, M.; King, M.; Lacasta, C.; Lacuesta, V.R.; Marti-Garcia, S.; Mitsou, V.A.; Moles-Valls, R.; Oliver Garcia, E.; Pedraza Lopez, S.; Perez Garcia-Estañ, M.T.; Romero Adam, E.; Ros, E.; Salt, J.; Sanchez Martinez, V.; Soldevila, U.; Sanchez, J.; Torro Pastor, E.; Valero, A.; Valladolid Gallego, E.; Valls Ferrer, J.A.; Vos, M. |
| Title |
Search for s-channel single top-quark production in proton-proton collisions at root s=8 TeV with the ATLAS detector |
Type |
Journal Article |
| Year |
2015 |
Publication |
Physics Letters B |
Abbreviated Journal |
Phys. Lett. B |
| Volume |
740 |
Issue |
|
Pages |
118-136 |
| Keywords |
ATLAS; Top quark; Electroweak production; s-Channel |
| Abstract |
This Letter presents a search at the LHC for s-channel single top-quark production in proton-proton collisions at a centre-of-mass energy of 8 TeV. The analyzed data set was recorded by the ATLAS detector and corresponds to an integrated luminosity of 20.3 fb(-1). Selected events contain one charged lepton, large missing transverse momentum and exactly two b-tagged jets. A multivariate event classifier based on boosted decision trees is developed to discriminate s-channel single top-quark events from the main background contributions. The signal extraction is based on a binned maximum-likelihood fit of the output classifier distribution. The analysis leads to an upper limit on the s-channel single topquark production cross-section of 14.6 pb at the 95% confidence level. The fit gives a cross-section of sigma(s) = 5.0 +/- 4.3 pb, consistent with the Standard Model expectation. |
| Address |
[Jackson, P.; Lee, L.; Leone, S.; Soni, N.; White, M. J.] Univ Adelaide, Dept Phys, Adelaide, SA, Australia |
| Corporate Author |
|
Thesis |
|
| Publisher |
Elsevier Science Bv |
Place of Publication |
|
Editor |
|
| Language |
English |
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0370-2693 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
WOS:000347046200017 |
Approved |
no |
| Is ISI |
yes |
International Collaboration |
yes |
| Call Number |
IFIC @ pastor @ |
Serial |
2095 |
| Permanent link to this record |
