Fujita, H. et al, Algora, A., Estevez-Aguado, E., Molina, F., & Rubio, B. (2019). Experimental study of Gamow-Teller transitions via the high-energy-resolution O-18(He-3, t)F-18 reaction: Identification of the low-energy “super” -Gamow-Teller state. Phys. Rev. C, 100(3), 034618–13pp.
Abstract: Using the high-resolution O-18(He-3, t)F-18 reaction at 0 degrees and at 140 MeV/nucleon, Gamow-Teller (GT) transitions were studied. A high energy resolution of 31 keV was achieved by applying dispersion matching techniques. The main part of the observed GT transition strength is concentrated in the transition to the F-18 ground state (g.s.). The absolute values of the reduced GT transition strengths, B(GT), were derived up to E-x = 12 MeV assuming proportionality between the B(GT) values and the reaction cross sections at 0 degrees. The B(GT) value obtained from the beta decay of F-18 (g.s.) -> O-18 (g.s.) was used to determine the proportionality constant. A total B(GT) of 4.06(5) was found and 76(1)% of the strength is concentrated to the ground state of F-18. The obtained B(GT) values were compared with those from the O-18(p, n) F-18 reaction and the mirror symmetric beta(+) decay of Ne-18 -> F-18. The candidates for 1(+) states with isospin T = 1 were identified by comparison with the O-18(p, p') data. The results of shell-model and quasiparticle-random-phase approximation calculations suggest constructive contributions of various configurations to the F-18 ground state, suggesting that this state is the low-energy super GT state.
|
Yokoyama, R. et al, Tain, J. L., Algora, A., Agramunt, J., Domingo-Pardo, C., Morales, A. I., et al. (2019). Strong one-neutron emission from two-neutron unbound states in beta decays of the r-process nuclei Ga-86,Ga-87. Phys. Rev. C, 100(3), 031302–6pp.
Abstract: beta-delayed one-neutron and two-neutron branching ratios (P-1n and P-2n) have been measured in the decay of A = 84 to 87 Ga isotopes at the Radioactive-Isotope Beam Factory (RIBF) at the RIKEN Nishina Center using a high-efficiency array of He-3 neutron counters (BRIKEN). Two-neutron emission was observed in the decay of Ga-84,Ga-85,Ga-87 for the first time and the branching ratios were measured to be P-2n = 1.6(2)%, 1.3(2)%, and 10.2(28)(stat)(5)(sys)%, respectively. One-neutron branching ratio of Ga-87 (P-1n = 81(9)(stat)(8)(sys)%) and half-life of 29(4) ms were measured for the first time. The branching ratios of Ga-86 were also measured to be P-1n = 74(2)(stat)(8)(sys)% and 16.2(9)(stat)(6)(sys)% with better precision than a previous study. The observation that P-1n > P-2n for both Ga-86,Ga-87 was unexpected and is interpreted as a signature of dominating one-neutron emission from the two-neutron unbound excited states in Ge-86,Ge-87. In order to interpret the experimental results, shell-model and Hauser-Feshbach statistical model calculations of delayed particle and gamma-ray emission probabilities were performed. This model framework reproduces the experimental results. The shell model alone predicts P-2n significantly larger than P-1n for the Ga-87 decay, and it is necessary to invoke a statistical description to successfully explain the observation that P-1n > P-2n. Our new results demonstrate the relevance and importance of a statistical description of neutron emission for the prediction of the decay properties of multineutron emitters and that it must be included in the r-process modeling.
|
AGATA Collaboration(Kaya, L. et al), & Gadea, A. (2019). Isomer spectroscopy in Ba-133 and high-spin structure of Ba-134. Phys. Rev. C, 100(2), 024323–18pp.
Abstract: The transitional nuclei Ba-134 and Ba-133 are investigated after multinucleon transfer employing the high-resolution Advanced GAmma Tracking Array coupled to the magnetic spectrometer PRISMA at the Laboratori Nazionali di Legnaro, Italy, and after fusion-evaporation reaction at the FN tandem accelerator of the University of Cologne, Germany. The J(pi) = 19/2(+) state at 1942 keV in Ba-133 is identified as an isomer with a half-life of 66.6(20) ns corresponding to a B(E1) value of 7.7(4) x 10(-6) e(2) fm(2) for the J(pi) = 19/2(+) to J(pi) = 19/2(-) transition. The level scheme of Ba-134 above the J(pi) = 10(+) isomer is extended to approximately 6 MeV. A pronounced backbending is observed at h omega = 0.38 MeV along the positive-parity yrast band. The results are compared to the high-spin systematics of the Z = 56 isotopes. Large-scale shell-model calculations employing the GCN50:82, SN100PN, SNV, PQM130, Realistic SM, and EPQQM interactions reproduce the experimental findings and elucidate the structure of the high-spin states. The shell-model calculations employing the GCN50:82 and PQM130 interactions reproduce alignment properties and provide detailed insight into the microscopic origin of this phenomenon in transitional Ba-134.
|
Phong, V. H. et al, Agramunt, J., Algora, A., Domingo-Pardo, C., Morales, A. I., Tain, J. L., et al. (2019). Observation of a μs isomer in In-134(49)85: Proton-neutron coupling “southeast” of Sn-132(50)82. Phys. Rev. C, 100(1), 011302–6pp.
Abstract: We report on the observation of a microsecond isomeric state in the single-proton-hole, three-neutron-particle nucleus In-134. The nuclei of interest were produced by in-flight fission of a U-238 beam at the Radioactive Isotope Beam Factory at RIKEN. The isomer depopulates through a gamma ray of energy 56.7(1) keV and with a half-life of T-1/2 = 3.5(4) μs. Based on the comparison with shell-model calculations, we interpret the isomer as the I-pi = 5(-) member of the pi 0g(9/2)(-1) circle times nu 1f(7/2)(3) multiplet, decaying to the I-pi = 7(-) ground state with a reduced-transition probability of B(E2; 5(-) -> 7(-)) = 0.53(6) W.u. Observation of this isomer, and lack of evidence in the current work for a I-pi = 5(-) isomer decay in In-132, provides a benchmark of the proton-neutron interaction in the region of the nuclear chart “southeast” of Sn-132, where experimental information on excited states is sparse.
|
Dudouet, J. et al, Gadea, A., & Perez-Vidal, R. M. (2019). Excitations of the magic N=50 neutron-core revealed in Ga-81. Phys. Rev. C, 100(1), 011301–6pp.
Abstract: The high-spin states of the neutron-rich Ga-81, with three valence protons outside a Ni-78 core, were measured. The measurement involved prompt gamma-ray spectroscopy of fission fragments isotopically identified using the combination of the variable mode spectrometer (VAMOS++) and the advanced gamma tracking array (AGATA). The new gamma-ray transitions, observed in coincidence with Ga-81 ions, and the corresponding level scheme do not confirm the high-spin levels reported earlier. The newly observed high-spin states in Ga-81 are interpreted using the results of state-of-the-art large-scale shell model (LSSM) calculations. The lower excitation energy levels are understood as resulting from the recoupling of three valence protons to the closed doubly magic core, while the highest excitation energy levels correspond to excitations of the magic N = 50 neutron core. These results support the doubly magic character of Ni-78 and the persistence of the N = 50 shell closure but also highlight the presence of strong proton-neutron correlations associated with the promotion of neutrons across the magic N = 50 shell gap, only few nucleons away from Ni-78.
|
Fuster-Martinez, N., Bruce, R., Hofer, M., Persson, T., Redaelli, S., & Tomas, R. (2022). Aperture measurements with ac dipoles and movable collimators in the Large Hadron Collider. Phys. Rev. Accel. Beams, 25(10), 101002–13pp.
Abstract: This paper presents a first experimental demonstration of a new nondestructive method for aperture measurements based on ac dipoles. In high intensity particle colliders, such as the CERN Large Hadron Collider (LHC), aperture measurements are crucial for a safe operation while optimizing the optics in order to reduce the size of the colliding beams and hence increase the luminosity. In the LHC, this type of measurements became mandatory during beam commissioning and the current method used is based on the destructive blowup of bunches using a transverse damper. The new method presented in this paper uses the ac-dipole excitation to generate adiabatic forced oscillations of the beam in order to create losses to identify the smallest aperture in the machine without blowing up the beam emittance. A precise and tuneable control of the oscillation amplitude enables the beams to be reused for several aperture measurements, as well as for other subsequent commissioning activities. Measurements performed with the new method are presented and compared with the current LHC transverse damper method for two different beam energies and two different operational optics.
|
Woolley, B., Burt, G., Dexter, A. C., Peacock, R., Millar, W. L., Catalan Lasheras, N., et al. (2020). High-gradient behavior of a dipole-mode rf structure. Phys. Rev. Accel. Beams, 23(12), 122002–11pp.
Abstract: A normal-conducting, X-band traveling wave structure operating in the dipole mode has been systematically high-gradient tested to gain insight into the maximum possible gradients in these types of structure. Measured structure conditioning, breakdown behavior, and achieved surface fields are reported as well as a postmortem analysis of the breakdown position and a scanning electron microscope analysis of the high-field surfaces. The results of these measurements are then compared to high-gradient results from monopole-mode cavities. Scaled to a breakdown rate of 10(-6), the cavities were found to operate at a peak electric field of 154 MV/m and a peak modified Poynting vector S-c of 5.48 MW/mm(2). The study provides important input for the further development of dipole-mode cavities for use in the Compact Linear Collider as a crab cavity and dipole-mode cavities for use in x-ray free-electron lasers as well as for studies of the fundamental processes in vacuum arcs. Of particular relevance are the unique field patterns in dipole cavities compared to monopole cavities, where the electric and magnetic fields peak in orthogonal planes, which allow the separation of the role of electric and magnetic fields in breakdown via postmortem damage observation. The azimuthal variation of breakdown crater density is measured and is fitted to sinusoidal functions. The best fit is a power law fit of exponent 6. This is significant, as it shows how breakdown probability varies over a surface area with a varying electric field after conditioning to a given peak field.
|
Vnuchenko, A., Esperante Pereira, D., Gimeno, B., Benedetti, S., Catalan Lasheras, N., Garlasch, M., et al. (2020). High-gradient testing of an S-band, normal-conducting low phase velocity accelerating structure. Phys. Rev. Accel. Beams, 23(8), 084801–13pp.
Abstract: A novel high-gradient accelerating structure with low phase velocity, v/c = 0.38, has been designed, manufactured and high-power tested. The structure was designed and built using the methodology and technology developed for CLIC 100 MV/m high-gradient accelerating structures, which have speed of light phase velocity, but adapts them to a structure for nonrelativistic particles. The parameters of the structure were optimized for the compact proton therapy linac project, and specifically to 76 MeV energy protons, but the type of structure opens more generally the possibility of compact low phase velocity linacs. The structure operates in S-band, is backward traveling wave (BTW) with a phase advance of 150 degrees and has an active length of 19 cm. The main objective for designing and testing this structure was to demonstrate that low velocity particles, in particular protons, can be accelerated with high gradients. In addition, the performance of this structure compared to other type of structures provides insights into the factors that limit high gradient operation. The structure was conditioned successfully to high gradient using the same protocol as for CLIC X-band structures. However, after the high power test, data analysis realized that the structure had been installed backwards, that is, the input power had been fed into what is nominally the output end of the structure. This resulted in higher peak fields at the power feed end and a steeply decreasing field profile along the structure, rather than the intended near constant field and gradient profile. A local accelerating gradient of 81 MV/m near the input end was achieved at a pulse length of 1.2 μs and with a breakdown rate (BDR) of 7.2 x 10(-7) 1 /pulse/m. The reverse configuration was accidental but the operating with this field condition gave very important insights into high-gradient behaviour and a comprehensive analysis has been carried out. A particular attention was paid to the characterization of the distribution of BD positions along the structure and within a cell.
|
Senes, E., Argyropoulos, T., Tecker, F., & Wuensch, W. (2018). Beam-loading effect on breakdown rate in high-gradient accelerating cavities: An experiment at the Compact Linear Collider Test Facility at CERN. Phys. Rev. Accel. Beams, 21(10), 102001–8pp.
Abstract: Radio frequency breakdown rate is a crucial performance parameter that ensures that the design luminosity is achieved in the CLIC linear collider. The required low breakdown rate for CLIC, of the order of 10(-7) breakdown pulse(-1) m(-1), has been demonstrated in a number of 12 GHz CLIC prototype structures at gradients in excess of the design 100 MV/m accelerating gradient, however without the presence of the accelerated beam and associated beam loading. The beam loading induced by the approximately 1 A CLIC main beam significantly modifies the field distribution inside the structures, and the effect on breakdown rate is potentially significant so needs to be determined. A dedicated experiment has been carried out in the CLIC Test Facility CTF3 to measure this effect, and the results are presented.
|
Argyropoulos, T., Catalan-Lasheras, N., Grudiev, A., Mcmonagle, G., Rodriguez-Castro, E., Syrachev, I., et al. (2018). Design, fabrication, and high-gradient testing of an X-band, traveling-wave accelerating structure milled from copper halves. Phys. Rev. Accel. Beams, 21(6), 061001–11pp.
Abstract: A prototype 11.994 GHz, traveling-wave accelerating structure for the Compact Linear Collider has been built, using the novel technique of assembling the structure from milled halves. The use of milled halves has many advantages when compared to a structure made from individual disks. These include the potential for a reduction in cost, because there are fewer parts, as well as a greater freedom in choice of joining technology because there are no rf currents across the halves' joint. Here we present the rf design and fabrication of the prototype structure, followed by the results of the high-power test and post-test surface analysis. During high-power testing the structure reached an unloaded gradient of 100 MV/m at a rf breakdown rate of less than 1.5 x 10(-5) breakdowns/pulse/m with a 200 ns pulse. This structure has been designed for the CLIC testing program but construction from halves can be advantageous in a wide variety of applications.
|
