Abstract: We present first evidence that the cosine of the CP-violating weak phase 2 beta is positive, and hence exclude trigonometric multifold solutions of the Cabibbo-Kobayashi-Maskawa (CKM) Unitarity Triangle using a time-dependent Dalitz plot analysis of B-0 -> D-(*) h(0) with D -> K-S(0)pi(+)pi(-) decays, where h(0) is an element of {pi(0), eta, omega} denotes a light unflavored and neutral hadron. The measurement is performed combining the final data sets of the BABAR and Belle experiments collected at the (sic)(4S) resonance at the asymmetric-energy B factories PEP-II at SLAC and KEKB at KEK, respectively. The data samples contain (471 +/- 3) x 10(6) B (B) over bar pairs recorded by the BABAR detector and (772 +/- 11) x 10(6) B (B) over bar pairs recorded by the Belle detector. The results of the measurement are sin 2 beta = 0.80 +/- 0.14 (stat) +/- 0.06 (syst) +/- 0.03 (model) and cos 2 beta = 0.91 +/- 0.22(stat) +/- 0.09 (syst) +/- 0.07(model). The result for the direct measurement of the angle beta of the CKM Unitarity Triangle is beta = [22.5 +/- 4.4 (stat) +/- 1.2 (syst) +/- 0.6(model)]degrees. The measurement assumes no direct CP violation in B-0 -> D-(*) h(0) decays. The quoted model uncertainties are due to the composition of the D-0 -> K-S(0)pi(+)pi(-) decay amplitude model, which is newly established by performing a Dalitz plot amplitude analysis using a high-statistics e(+)e(-) -> c (c) over bar data sample. CP violation is observed in B-0 -> D-(*) h(0) decays at the level of 5.1 standard deviations. The significance for cos 2 beta > 0 is 3.7 standard deviations. The trigonometric multifold solution pi/2 – beta = (68.1 +/- 0.7)degrees is excluded at the level of 7.3 standard deviations. The measurement resolves an ambiguity in the determination of the apex of the CKM Unitarity Triangle.

Abstract: This paper describes the electronics of NEXT-White (NEW) detector PMT plane, a high pressure xenon TPC with electroluminescent amplification (HPXe-EL) currently operating at the Laboratorio Subterraneo de Canfranc (LSC) in Huesca, Spain. In NEXT-White the energy of the event is measured by a plane of photomultipliers (PMTs) located behind a transparent cathode. The PMTs are Hamamatsu R11410-10 chosen due to their low radioactivity. The electronics have been designed and implemented to fulfill strict requirements: an overall energy resolution below 1% and a radiopurity budget of 20 mBq unit(-1) in the chain of Bi-214. All the components and materials have been carefully screened to assure a low radioactivity level and at the same time meet the required front-end electronics specifications. In order to reduce low frequency noise effects and enhance detector safety a grounded cathode connection has been used for the PMTs. This implies an AC-coupled readout and baseline variations in the PMT signals. A detailed description of the electronics and a novel approach based on a digital baseline restoration to obtain a linear response and handle AC coupling effects is presented. The final PMT channel design has been characterized with linearity better than 0.4% and noise below 0.4 mV.

Abstract: The Tile Calorimeter is the hadron calorimeter covering the central region of the ATLAS experiment at the Large Hadron Collider. Approximately 10,000 photomultipliers collect light from scintillating tiles acting as the active material sandwiched between slabs of steel absorber. This paper gives an overview of the calorimeter's performance during the years 2008-2012 using cosmic-ray muon events and proton-proton collision data at centre-of-mass energies of 7 and 8 TeV with a total integrated luminosity of nearly 30 fb(-1). The signal reconstruction methods, calibration systems as well as the detector operation status are presented. The energy and time calibration methods performed excellently, resulting in good stability of the calorimeter response under varying conditions during the LHC Run 1. Finally, the Tile Calorimeter response to isolated muons and hadrons as well as to jets from proton-proton collisions is presented. The results demonstrate excellent performance in accord with specifications mentioned in the Technical Design Report.