|
BABAR Collaboration(del Amo Sanchez, P. et al), Lopez-March, N., Martinez-Vidal, F., & Oyanguren, A. (2011). Dalitz plot analysis of D-s(+) -> K+ K- pi(+). Phys. Rev. D, 83(5), 052001–20pp.
Abstract: We perform a Dalitz plot analysis of about 100 000 D-s(+) decays to K+ K- pi(+) and measure the complex amplitudes of the intermediate resonances which contribute to this decay mode. We also measure the relative branching fractions of D-s(+) -> K+ K+ pi(-) and D-s(+) -> K+ K+ K-. For this analysis we use a 384 fb(-1) data sample, recorded by the BABAR detector at the PEP-II asymmetric-energy e(+)e(-) collider running at center-of-mass energies near 10.58 GeV.
|
|
|
Molina, R., Nagahiro, H., Hosaka, A., & Oset, E. (2011). Decay of vector-vector resonances into gamma and a pseudoscalar meson. Phys. Rev. D, 83(9), 094030–12pp.
Abstract: We study the decay of dynamically generated resonances from the interaction of two vectors into a gamma and a pseudoscalar meson. The dynamics requires anomalous terms involving vertices with two vectors and a pseudoscalar, which renders it special. We compare our result with data on K-2*(+) (1430) -> K+ gamma and K-2*(0) (1430) -> K-0 gamma and find a good agreement with the data for the K-2*(+) (1430) case and a width considerably smaller than the upper bound measured for the K-2*(0) (1430) meson. We also investigate the decay into pi(+) gamma of one a(2) state, tentatively associated to the a(2)(1320), obtaining qualitative agreement with data.
|
|
|
Nieves, J., & Valderrama, M. P. (2011). Deriving the existence of B(B)over-bar* bound states from the X(3872) and heavy quark symmetry. Phys. Rev. D, 84(5), 056015–21pp.
Abstract: We discuss the possibility and the description of bound states between B and (B) over bar* mesons. We argue that the existence of such a bound state can be deduced from (i) the weakly bound X(3872) state, (ii) certain assumptions about the short-range dynamics of the D (D) over bar* system and (iii) heavy quark symmetry. From these assumptions the binding energy of the possible B (B) over bar* bound states is determined, first in a theory containing only contact interactions which serves as a straightforward illustration of the method, and then the effects of including the one-pion exchange potential are discussed. In this latter case three isoscalar states are predicted: a positive and negative C-parity (3)S(1) – (3)D(1) state with a binding energy of 20 MeV and 6 MeV below threshold, respectively, and a positive C-parity (3)P(0) shallow state located almost at the B (B) over bar* threshold. However, large uncertainties are generated as a consequence of the 1/m(Q) corrections from heavy quark symmetry. Finally, the newly discovered isovector Z(b)(10610) state can be easily accommodated within the present framework by a minor modification of the short-range dynamics.
|
|
|
Li, X. Q., Su, F., & Yang, Y. D. (2011). Determination of the strong coupling gB*B pi from semileptonic B -> pi l nu decay. Phys. Rev. D, 83(5), 054019–8pp.
Abstract: According to heavy-meson chiral perturbation theory, the vector form factor f+(q(2)) of exclusive semileptonic decay B -> pi l nu is closely related, at least in the soft-pion region ( i.e., q(2) similar to (m(B) – m(pi))(2)), to the strong coupling g(B*B pi) or the normalized coupling (g)over-cap. Combining the precisely measured q2 spectrum of B -> pi l nu decay by the BABAR and Belle collaborations with several parametrizations of the form factor f +(q(2)), we can extract these couplings from the residue of the form factor at the B* pole, which relies on an extrapolation of the form factor from the semileptonic region to the unphysical point q(2) = m(B*)(2). Comparing the extracted values with the other experimental and theoretical estimates, we can test these various form-factor parametrizations, which differ from each other by the amount of physical information embedded in. It is found that the extracted values based on the Becirevic-Kaidalov, Ball-Zwicky and Bourrely-Caprini-Lellouch parametrizations are consistent with each other and roughly in agreement with the other theoretical and lattice estimates, while the Boyd-Grinstein-Lebed ansatz, featured by a spurious, unwanted pole at the threshold of the cut, gives a neatly larger value.
|
|
|
Marco-Hernandez, R. (2011). Development of a beam test telescope based on the Alibava readout system. J. Instrum., 6, C01002–7pp.
Abstract: A telescope for a beam test have been developed as a result of a collaboration among the University of Liverpool, Centro Nacional de Microelectronica (CNM) of Barcelona and Instituto de Fisica Corpuscular (IFIC) of Valencia. This system is intended to carry out both analogue charge collection and spatial resolution measurements with different types of microstrip or pixel silicon detectors in a beam test environment. The telescope has four XY measurement as well as trigger planes (XYT board) and it can accommodate up to twelve devices under test (DUT board). The DUT board uses two Beetle ASICs for the readout of chilled silicon detectors. The board could operate in a self-triggering mode. The board features a temperature sensor and it can be mounted on a rotary stage. A peltier element is used for cooling the DUT. Each XYT board measures the track space points using two silicon strip detectors connected to two Beetle ASICs. It can also trigger on the particle tracks in the beam test. The board includes a CPLD which allows for the synchronization of the trigger signal to a common clock frequency, delaying and implementing coincidence with other XYT boards. An Alibava mother board is used to read out and to control each XYT/DUT board from a common trigger signal and a common clock signal. The Alibava board has a TDC on board to have a time stamp of each trigger. The data collected by each Alibava board is sent to a master card by means of a local data/address bus following a custom digital protocol. The master board distributes the trigger, clock and reset signals. It also merges the data streams from up to sixteen Alibava boards. The board has also a test channel for testing in a standard mode a XYT or DUT board. This board is implemented with a Xilinx development board and a custom patch board. The master board is connected with the DAQ software via 100M Ethernet. Track based alignment software has also been developed for the data obtained with the DAQ software.
|
|