|
ATLAS Collaboration(Aad, G. et al), Alvarez Piqueras, D., Cabrera Urban, S., Castillo Gimenez, V., Cerda Alberich, L., Costa, M. J., et al. (2017). Topological cell clustering in the ATLAS calorimeters and its performance in LHC Run 1. Eur. Phys. J. C, 77(7), 490–73pp.
Abstract: The reconstruction of the signal from hadrons and jets emerging from the proton-proton collisions at the Large Hadron Collider (LHC) and entering the ATLAS calorimeters is based on a three-dimensional topological clustering of individual calorimeter cell signals. The cluster formation follows cell signal-significance patterns generated by electromagnetic and hadronic showers. In this, the clustering algorithm implicitly performs a topological noise suppression by removing cells with insignificant signals which are not in close proximity to cells with significant signals. The resulting topological cell clusters have shape and location information, which is exploited to apply a local energy calibration and corrections depending on the nature of the cluster. Topological cell clustering is established as a well-performing calorimeter signal definition for jet and missing transverse momentum reconstruction in ATLAS.
|
|
|
ATLAS Collaboration(Aaboud, M. et al), Alvarez Piqueras, D., Barranco Navarro, L., Cabrera Urban, S., Castillo Gimenez, V., Cerda Alberich, L., et al. (2017). Top-quark mass measurement in the all-hadronic t(t)over-bar decay channel at root s=8 TeV with the ATLAS detector. J. High Energy Phys., 09(9), 118–41pp.
Abstract: The top-quark mass is measured in the all-hadronic top-antitop quark decay channel using proton-proton collisions at a centre-of-mass energy of root s = 8 TeV with the ATLAS detector at the CERN Large Hadron Collider. The data set used in the analysis corresponds to an integrated luminosity of 20.2 fb(-1). The large multi-jet background is modelled using a data-driven method. The top-quark mass is obtained from template fits to the ratio of the three-jet to the dijet mass. The three-jet mass is obtained from the three jets assigned to the top quark decay. From these three jets the dijet mass is obtained using the two jets assigned to the W boson decay. The top-quark mass is measured to be 173.72 +/- 0.55 (stat.) +/- 1.01 (syst.) GeV.
|
|
|
ATLAS Collaboration(Aad, G. et al), Amos, K. R., Aparisi Pozo, J. A., Bailey, A. J., Bouchhar, N., Cabrera Urban, S., et al. (2023). Tools for estimating fake/non-prompt lepton backgrounds with the ATLAS detector at the LHC. J. Instrum., 18(11), T11004–61pp.
Abstract: Measurements and searches performed with the ATLAS detector at the CERN LHC often involve signatures with one or more prompt leptons. Such analyses are subject to 'fake/non-prompt' lepton backgrounds, where either a hadron or a lepton from a hadron decay or an electron from a photon conversion satisfies the prompt-lepton selection criteria. These backgrounds often arise within a hadronic jet because of particle decays in the showering process, particle misidentification or particle interactions with the detector material. As it is challenging to model these processes with high accuracy in simulation, their estimation typically uses data-driven methods. Three methods for carrying out this estimation are described, along with their implementation in ATLAS and their performance.
|
|
|
Studen, A., Burdette, D., Chesi, E., Cindro, V., Clinthorne, N. H., Cochran, E., et al. (2010). Timing performance of the silicon PET insert probe. Radiat. Prot. Dosim., 139(1-3), 199–203.
Abstract: Simulation indicates that PET image could be improved by upgrading a conventional ring with a probe placed close to the imaged object. In this paper, timing issues related to a PET probe using high-resistivity silicon as a detector material are addressed. The final probe will consist of several (four to eight) 1-mm thick layers of silicon detectors, segmented into 1 x 1 mm(2) pads, each pad equivalent to an independent p + nn+ diode. A proper matching of events in silicon with events of the external ring can be achieved with a good timing resolution. To estimate the timing performance, measurements were performed on a simplified model probe, consisting of a single 1-mm thick detector with 256 square pads (1.4 mm side), coupled with two VATAGP7s, application-specific integrated circuits. The detector material and electronics are the same that will be used for the final probe. The model was exposed to 511 keV annihilation photons from an Na-22 source, and a scintillator (LYSO)-PMT assembly was used as a timing reference. Results were compared with the simulation, consisting of four parts: (i) GEANT4 implemented realistic tracking of electrons excited by annihilation photon interactions in silicon, (ii) calculation of propagation of secondary ionisation (electron-hole pairs) in the sensor, (iii) estimation of the shape of the current pulse induced on surface electrodes and (iv) simulation of the first electronics stage. A very good agreement between the simulation and the measurements were found. Both indicate reliable performance of the final probe at timing windows down to 20 ns.
|
|
|
ATLAS Collaboration(Aad, G. et al), Cabrera Urban, S., Castillo Gimenez, V., Costa, M. J., Fassi, F., Ferrer, A., et al. (2012). Time-dependent angular analysis of the decay B-s(0) -> J/psi phi and extraction of Delta Gamma(s) and the CP-violating weak phase phi(s) by ATLAS. J. High Energy Phys., 12(12), 072–34pp.
Abstract: A measurement of B-s(0) -> J/psi phi decay parameters, including the CP-violating weak phase phi(s) and the decay width difference Delta Gamma(s) is reported, using 4.9 fb(-1) of integrated luminosity collected in 2011 by the ATLAS detector from LHC pp collisions at a centre-of-mass energy root s = 7 TeV. The mean decay width Gamma(s) and the transversity amplitudes vertical bar A(0)(0)vertical bar(2) and vertical bar A(parallel to)(0)vertical bar(2) are also measured. The values reported for these parameters are: phi(s) = 0.22 +/- 0.41 (stat.) +/- 0.10 (syst.) rad Delta Gamma(s) = 0.053 +/- 0.021 (stat.) +/- 0.010 (syst.) ps(-1) Gamma(s) = 0.677 +/- 0.007 (stat.) +/- 0.004 (syst.) ps(-1) vertical bar A(0)(0)vertical bar(2) = 0.528 +/- 0.006 (stat.) +/- 0.009 (syst.) vertical bar A(parallel to)(0)vertical bar(2) = 0.220 +/- 0.008 (stat.) +/- 0.007 (syst.) where the values quoted for phi(s) and Delta Gamma(s) correspond to the solution compatible with the external measurements to which the strong phase delta(perpendicular to) is constrained and where is Delta Gamma(s) constrained to be positive. The fraction of S-wave KK or f(0) contamination through the decays B-s(0) -> J/psi K+K- (f(0)) is measured as well and is found to be consistent with zero. Results for phi(s) and Delta Gamma(s) are also presented as 68%, 90% and 95% likelihood contours, which show agreement with Standard Model expectations.
|
|