|
ATLAS Collaboration(Aad, G. et al), Cabrera Urban, S., Castillo Gimenez, V., Costa, M. J., Ferrer, A., Fiorini, L., et al. (2012). Underlying event characteristics and their dependence on jet size of charged-particle jet events in pp collisions at root(s)=7 TeV with the ATLAS detector. Phys. Rev. D, 86(7), 072004–34pp.
Abstract: Distributions sensitive to the underlying event are studied in events containing one or more chargedparticle jets produced in pp collisions at root s = 7 TeV with the ATLAS detector at the Large Hadron Collider (LHC). These measurements reflect 800 μb(-1) of data taken during 2010. Jets are reconstructed using the anti-k(t) algorithm with radius parameter R varying between 0.2 and 1.0. Distributions of the charged-particle multiplicity, the scalar sum of the transverse momentum of charged particles, and the average charged-particle p(T) are measured as functions of p(T)(jet) in regions transverse to and opposite the leading jet for 4 GeV < p(T)(jet) < 100 GeV. In addition, the R dependence of the mean values of these observables is studied. In the transverse region, both the multiplicity and the scalar sum of the transverse momentum at fixed p(T)(jet) vary significantly with R, while the average charged- particle transverse momentum has a minimal dependence on R. Predictions from several Monte Carlo tunes have been compared to the data; the predictions from Pythia 6, based on tunes that have been determined using LHC data, show reasonable agreement with the data, including the dependence on R. Comparisons with other generators indicate that additional tuning of soft-QCD parameters is necessary for these generators. The measurements presented here provide a testing ground for further development of the Monte Carlo models.
|
|
|
ATLAS Collaboration(Aad, G. et al), Cabrera Urban, S., Castillo Gimenez, V., Costa, M. J., Fassi, F., Ferrer, A., et al. (2012). Time-dependent angular analysis of the decay B-s(0) -> J/psi phi and extraction of Delta Gamma(s) and the CP-violating weak phase phi(s) by ATLAS. J. High Energy Phys., 12(12), 072–34pp.
Abstract: A measurement of B-s(0) -> J/psi phi decay parameters, including the CP-violating weak phase phi(s) and the decay width difference Delta Gamma(s) is reported, using 4.9 fb(-1) of integrated luminosity collected in 2011 by the ATLAS detector from LHC pp collisions at a centre-of-mass energy root s = 7 TeV. The mean decay width Gamma(s) and the transversity amplitudes vertical bar A(0)(0)vertical bar(2) and vertical bar A(parallel to)(0)vertical bar(2) are also measured. The values reported for these parameters are: phi(s) = 0.22 +/- 0.41 (stat.) +/- 0.10 (syst.) rad Delta Gamma(s) = 0.053 +/- 0.021 (stat.) +/- 0.010 (syst.) ps(-1) Gamma(s) = 0.677 +/- 0.007 (stat.) +/- 0.004 (syst.) ps(-1) vertical bar A(0)(0)vertical bar(2) = 0.528 +/- 0.006 (stat.) +/- 0.009 (syst.) vertical bar A(parallel to)(0)vertical bar(2) = 0.220 +/- 0.008 (stat.) +/- 0.007 (syst.) where the values quoted for phi(s) and Delta Gamma(s) correspond to the solution compatible with the external measurements to which the strong phase delta(perpendicular to) is constrained and where is Delta Gamma(s) constrained to be positive. The fraction of S-wave KK or f(0) contamination through the decays B-s(0) -> J/psi K+K- (f(0)) is measured as well and is found to be consistent with zero. Results for phi(s) and Delta Gamma(s) are also presented as 68%, 90% and 95% likelihood contours, which show agreement with Standard Model expectations.
|
|
|
ATLAS Tile Calorimeter Community(Abdallah, J. et al), Castillo Gimenez, V., Costelo, J., Ferrer, A., Fullana, E., Gonzalez, V., et al. (2013). The optical instrumentation of the ATLAS Tile Calorimeter. J. Instrum., 8, P01005–21pp.
Abstract: The Tile Calorimeter, covering the central region of the ATLAS experiment up to pseudorapidities of +/-1.7, is a sampling device built with scintillating tiles that alternate with iron plates. The light is collected in wave-length shifting (WLS) fibers and is read out with photomultipliers. In the characteristic geometry of this calorimeter the tiles lie in planes perpendicular to the beams, resulting in a very simple and modular mechanical and optical layout. This paper focuses on the procedures applied in the optical instrumentation of the calorimeter, which involved the assembly of about 460,000 scintillator tiles and 550,000 WLS fibers. The outcome is a hadronic calorimeter that meets the ATLAS performance requirements, as shown in this paper.
|
|
|
ATLAS Tile Calorimeter System(Abdallah, J. et al), Ferrer, A., Fiorini, L., Hernandez Jimenez, Y., Higon-Rodriguez, E., Ruiz-Martinez, A., et al. (2016). The Laser calibration of the ATLAS Tile Calorimeter during the LHC run 1. J. Instrum., 11, T10005–29pp.
Abstract: This article describes the Laser calibration system of the ATLAS hadronic Tile Calorimeter that has been used during the run 1 of the LHC. First, the stability of the system associated readout electronics is studied. It is found to be stable with variations smaller than 0.6 %. Then, the method developed to compute the calibration constants, to correct for the variations of the gain of the calorimeter photomultipliers, is described. These constants were determined with a statistical uncertainty of 0.3 % and a systematic uncertainty of 0.2 % for the central part of the calorimeter and 0.5 % for the end-caps. Finally, the detection and correction of timing mis-configuration of the Tile Calorimeter using the Laser system are also presented.
|
|
|
Valero, A., Castillo Gimenez, V., Ferrer, A., Gonzalez, V., Hernandez Jimenez, Y., Higon-Rodriguez, E., et al. (2011). The ATLAS tile calorimeter ROD injector and multiplexer board. Nucl. Instrum. Methods Phys. Res. A, 629(1), 74–79.
Abstract: The ATLAS Tile Calorimeter is a sampling detector composed by cells made of iron-scintillator tiles. The calorimeter cell signals are digitized in the front-end electronics and transmitted to the Read-Out Drivers (RODs) at the first level trigger rate. The ROD receives triggered data from up to 9856 channels and provides the energy, phase and quality factor of the signals to the second level trigger. The back-end electronics is divided into four partitions containing eight RODs each. Therefore, a total of 32 RODs are used to process and transmit the data of the TileCal detector. In order to emulate the detector signals in the production and commissioning of ROD modules a board called ROD Injector and Multiplexer Board (RIMBO) was designed. In this paper, the RIMBO main functional blocks, PCB design and the different operation modes are described. It is described the crucial role of the board within the TileCal ROD test-bench in order to emulate the front-end electronics during the validation of ROD boards as well as during the evaluation of the ROD signal reconstruction algorithms. Finally, qualification and performance results for the injection operation mode obtained during the Tile Calorimeter ROD production tests are presented.
|
|