| |
Records |
Links |
|
Author |
KM3NeT Collaboration (Aiello, S. et al); Calvo, D.; Coleiro, A.; Colomer, M.; Gozzini, S.R.; Hernandez-Rey, J.J.; Illuminati, G.; Khan Chowdhury, N.R.; Manczak, J.; Pieterse, C.; Real, D.; Thakore, T.; Zornoza, J.D.; Zuñiga, J. |
|
| |
Title |
KM3NeT front-end and readout electronics system: hardware, firmware, and software |
Type |
Journal Article |
| |
Year |
2019 |
Publication |
Journal of Astronomical Telescopes, Instruments and Systems |
Abbreviated Journal |
J. Astron. Telesc. Instrum. Syst. |
|
| |
Volume |
5 |
Issue |
4 |
Pages |
046001 - 15pp |
|
| |
Keywords |
front-end electronics; readout electronics; neutrino telescope; KM3NeT |
|
| |
Abstract |
The KM3NeT research infrastructure being built at the bottom of the Mediterranean Sea will host water-Cherenkov telescopes for the detection of cosmic neutrinos. The neutrino telescopes will consist of large volume three-dimensional grids of optical modules to detect the Cherenkov light from charged particles produced by neutrino-induced interactions. Each optical module houses 31 3-in. photomultiplier tubes, instrumentation for calibration of the photomultiplier signal and positioning of the optical module, and all associated electronics boards. By design, the total electrical power consumption of an optical module has been capped at seven Watts. We present an overview of the front-end and readout electronics system inside the optical module, which has been designed for a 1-ns synchronization between the clocks of all optical modules in the grid during a life time of at least 20 years. (C) 2019 Society of Photo-Optical Instrumentation Engineers (SPIE) |
|
| |
Address |
[Aiello, Sebastiano; Leonora, Emanuele; Longhitano, Fabio; Randazzo, Nunzio] INFN, Sez Catania, Catania, Italy, Email: v.van.beveren@nikhef.nl; |
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
Spie-Soc Photo-Optical Instrumentation Engineers |
Place of Publication |
|
Editor |
|
|
| |
Language |
English |
Summary Language |
|
Original Title |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
2329-4124 |
ISBN  |
|
Medium |
|
|
| |
Area |
|
Expedition |
|
Conference |
|
|
| |
Notes |
WOS:000510649500024 |
Approved |
no |
|
| |
Is ISI |
yes |
International Collaboration |
yes |
|
| |
Call Number |
IFIC @ pastor @ |
Serial |
4282 |
|
| Permanent link to this record |
| |
|
| |
|
Author |
Poley, L. et al; Bernabeu, J.; Civera, J.V.; Lacasta, C.; Leon, P.; Platero, A.; Platero, V; Solaz, C.; Soldevila, U.; Vidal, G. |
|
| |
Title |
The ABC130 barrel module prototyping programme for the ATLAS strip tracker |
Type |
Journal Article |
| |
Year |
2020 |
Publication |
Journal of Instrumentation |
Abbreviated Journal |
J. Instrum. |
|
| |
Volume |
15 |
Issue |
9 |
Pages |
P09004 - 78pp |
|
| |
Keywords |
Detector design and construction technologies and materials; Si microstrip and pad detectors; Radiation-hard detectors; Front-end electronics for detector readout |
|
| |
Abstract |
For the Phase-II Upgrade of the ATLAS Detector [1], its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100% silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000 modules in the forward region (end-caps), which are foreseen to be constructed over a period of 3.5 years. The construction of each module consists of a series of assembly and quality control steps, which were engineered to be identical for all production sites. In order to develop the tooling and procedures for assembly and testing of these modules, two series of major prototyping programs were conducted: an early program using readout chips designed using a 250 nm fabrication process (ABCN-250) [2, 3] and a subsequent program using a follow-up chip set made using 130 nm processing (ABC130 and HCC130 chips). This second generation of readout chips was used for an extensive prototyping program that produced around 100 barrel-type modules and contributed significantly to the development of the final module layout. This paper gives an overview of the components used in ABC130 barrel modules, their assembly procedure and findings resulting from their tests. |
|
| |
Address |
[Poley, L.; Anderssen, E.; Ciocio, A.; Cornell, E.; Haber, C.; Haugen, T. E.; Heim, T.; Johnson, T. A.; Krizka, K.; Labitan, C.; Li, B.; Li, C.; MacFadyen, R.; Mladina, E.; Ottino, G.; Sanethavong, P.; Santpur, S. Neha; Witharm, R.] Lawrence Berkeley Natl Lab, Cyclotron Rd, Berkeley, CA 94720 USA, Email: APoley@cern.ch |
|
| |
Corporate Author |
|
Thesis |
|
|
| |
Publisher |
Iop Publishing Ltd |
Place of Publication |
|
Editor |
|
|
| |
Language |
English |
Summary Language |
|
Original Title |
|
|
| |
Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
|
| |
Series Volume |
|
Series Issue |
|
Edition |
|
|
| |
ISSN |
1748-0221 |
ISBN |
|
Medium |
|
|
| |
Area |
|
Expedition |
|
Conference |
|
|
| |
Notes |
WOS:000577273400004 |
Approved |
no |
|
| |
Is ISI |
yes |
International Collaboration |
yes |
|
| |
Call Number |
IFIC @ pastor @ |
Serial |
4572 |
|
| Permanent link to this record |
