ATLAS Collaboration(Aad, G. et al), Aparisi Pozo, J. A., Bailey, A. J., Cabrera Urban, S., Castillo, F. L., Castillo Gimenez, V., et al. (2020). Performance of the ATLAS muon triggers in Run 2. J. Instrum., 15(9), P09015–57pp.
Abstract: The performance of the ATLAS muon trigger system is evaluated with proton-proton (pp) and heavy-ion (HI) collision data collected in Run 2 during 2015-2018 at the Large Hadron Collider. It is primarily evaluated using events containing a pair of muons from the decay of Z bosons to cover the intermediate momentum range between 26 GeV and 100 GeV. Overall, the efficiency of the single-muon triggers is about 68% in the barrel region and 85% in the endcap region. The p(T) range for efficiency determination is extended by using muons from decays of J/psi mesons, W bosons, and top quarks. The performance in HI collision data is measured and shows good agreement with the results obtained in pp collisions. The muon trigger shows uniform and stable performance in good agreement with the prediction of a detailed simulation. Dedicated multi-muon triggers with kinematic selections provide the backbone to beauty, quarkonia, and low-mass physics studies. The design, evolution and performance of these triggers are discussed in detail.
|
ATLAS Collaboration(Aad, G. et al), Aparisi Pozo, J. A., Bailey, A. J., Cabrera Urban, S., Castillo, F. L., Castillo Gimenez, V., et al. (2020). Alignment of the ATLAS Inner Detector in Run 2. Eur. Phys. J. C, 80(12), 1194–41pp.
Abstract: The performance of the ATLAS Inner Detector alignment has been studied using pp collision data at v s = 13 TeV collected by the ATLAS experiment during Run 2 (2015-2018) of the Large Hadron Collider (LHC). The goal of the detector alignment is to determine the detector geometry as accurately as possible and correct for time-dependent movements. The Inner Detector alignment is based on the minimization of track-hit residuals in a sequence of hierarchical levels, from global mechanical assembly structures to local sensors. Subsequent levels have increasing numbers of degrees of freedom; in total there are almost 750,000. The alignment determines detector geometry on both short and long timescales, where short timescales describe movementswithin anLHCfill. The performance and possible track parameter biases originating from systematic detector deformations are evaluated. Momentum biases are studied using resonances decaying to muons or to electrons. The residual sagitta bias and momentum scale bias after alignment are reduced to less than similar to 0.1 TeV-1 and 0.9 x 10(-3), respectively. Impact parameter biases are also evaluated using tracks within jets.
|
ATLAS Collaboration(Aaboud, M. et al), Alvarez Piqueras, D., Aparisi Pozo, J. A., Bailey, A. J., Barranco Navarro, L., Cabrera Urban, S., et al. (2019). Performance of top-quark and W-boson tagging with ATLAS in Run 2 of the LHC. Eur. Phys. J. C, 79(5), 375–54pp.
Abstract: The performance of identification algorithms (taggers) for hadronically decaying top quarks and W bosons in pp collisions at = 13TeV recorded by the ATLAS experiment at the Large Hadron Collider is presented. A set of techniques based on jet shape observables are studied to determine a set of optimal cut-based taggers for use in physics analyses. The studies are extended to assess the utility of combinations of substructure observables as a multivariate tagger using boosted decision trees or deep neural networks in comparison with taggers based on two-variable combinations. In addition, for highly boosted top-quark tagging, a deep neural network based on jet constituent inputs as well as a re-optimisation of the shower deconstruction technique is presented. The performance of these taggers is studied in data collected during 2015 and 2016 corresponding to 36.1fb-1 for the tt and +jet and 36.7-1 for the dijet event topologies.
|
ATLAS Collaboration(Aad, G. et al), Aparisi Pozo, J. A., Bailey, A. J., Cabrera Urban, S., Cardillo, F., Castillo, F. L., et al. (2021). Measurements of Higgs bosons decaying to bottom quarks from vvector boson fusion production with the ATLAS experiment at root s=13 TeV. Eur. Phys. J. C, 81(6), 537–32pp.
Abstract: The paper presents a measurement of the Standard Model Higgs Boson decaying to b-quark pairs in the vector boson fusion (VBF) production mode. A sample corresponding to 126 fb(-1) of root s = 13 TeVproton-proton collision data, collected with the ATLAS experiment at the Large Hadron Collider, is analyzed utilizing an adversarial neural network for event classification. The signal strength, defined as the ratio of the measured signal yield to that predicted by the Standard Model for VBF Higgs production, is measured to be 0.95(-0.36)(+0.38), corresponding to an observed (expected) significance of 2.6 (2.8) standard deviations from the background only hypothesis. The results are additionally combined with an analysis of Higgs bosons decaying to b-quarks, produced via VBF in association with a photon.
|
ATLAS Collaboration(Aad, G. et al), Aparisi Pozo, J. A., Bailey, A. J., Cabrera Urban, S., Cardillo, F., Castillo, F. L., et al. (2020). Observation and Measurement of Forward Proton Scattering in Association with Lepton Pairs Produced via the Photon Fusion Mechanism at ATLAS. Phys. Rev. Lett., 125(26), 261801–21pp.
Abstract: The observation of forward proton scattering in association with lepton pairs (e(+)e(-) + p or mu(+)mu(-) + p) produced via photon fusion is presented. The scattered proton is detected by the ATLAS Forward Proton spectrometer, while the leptons are reconstructed by the central ATLAS detector. Proton-proton collision data recorded in 2017 at a center-of-mass energy of root s = 13 TeV are analyzed, corresponding to an integrated luminosity of 14.6 fb(-1). A total of 57 (123) candidates in the ee + p (mu μ+ p) final state arc selected, allowing the background-only hypothesis to be rejected with a significance exceeding 5 standard deviations in each channel. Proton-tagging techniques are introduced for cross-section measurements in the fiducial detector acceptance, corresponding to sigma(ee)(+p) = 11.0 +/- 2.6(stat) 1.2(syst) +/- 0.3(lumi) and sigma(mu)(mu+)(p) = 7.2 +/- 1.6(stat) +/- 0.9(syst) 0.2(lumi) fb in the dielectron and dimuon channel, respectively.
|
ATLAS Collaboration(Aad, G. et al), Alvarez Piqueras, D., Aparisi Pozo, J. A., Bailey, A. J., Barranco Navarro, L., Cabrera Urban, S., et al. (2019). Resolution of the ATLAS muon spectrometer monitored drift tubes in LHC Run 2. J. Instrum., 14, P09011–35pp.
Abstract: The momentum measurement capability of the ATLAS muon spectrometer relies fundamentally on the intrinsic single-hit spatial resolution of the monitored drift tube precision tracking chambers. Optimal resolution is achieved with a dedicated calibration program that addresses the specific operating conditions of the 354 000 high-pressure drift tubes in the spectrometer. The calibrations consist of a set of timing offsets and drift time to drift distance transfer relations, and result in chamber resolution functions. This paper describes novel algorithms to obtain precision calibrations from data collected by ATLAS in LHC Run 2 and from a gas monitoring chamber, deployed in a dedicated gas facility. The algorithm output consists of a pair of correction constants per chamber which are applied to baseline calibrations, and determined to be valid for the entire ATLAS Run 2. The final single-hit spatial resolution, averaged over 1172 monitored drift tube chambers, is 81.7 +/- 2.2 μm.
|
ATLAS Collaboration(Aaboud, M. et al), Alvarez Piqueras, D., Bailey, A. J., Barranco Navarro, L., Cabrera Urban, S., Castillo, F. L., et al. (2020). Determination of jet calibration and energy resolution in proton-proton collisions at s=8 TeV using the ATLAS detector. Eur. Phys. J. C, 80(12), 1104–81pp.
Abstract: The jet energy scale, jet energy resolution, and their systematic uncertainties are measured for jets reconstructed with the ATLAS detector in 2012 using proton-proton data produced at a centre-of-mass energy of 8 TeV with an integrated luminosity of 20 fb-1. Jets are reconstructed from clusters of energy depositions in the ATLAS calorimeters using the anti-kt algorithm. A jet calibration scheme is applied in multiple steps, each addressing specific effects including mitigation of contributions from additional proton-proton collisions, loss of energy in dead material, calorimeter non-compensation, angular biases and other global jet effects. The final calibration step uses several in situ techniques and corrects for residual effects not captured by the initial calibration. These analyses measure both the jet energy scale and resolution by exploiting the transverse momentum balance in gamma + jet, Z + jet, dijet, and multijet events. A statistical combination of these measurements is performed. In the central detector region, the derived calibration has a precision better than 1% for jets with transverse momentum 150 GeV<pT< 1500 GeV, and the relative energy resolution is (8.4 +/- 0.6)% for pT=100 GeV and (23 +/- 2)% for pT=20 GeV. The calibration scheme for jets with radius parameter R=1.0, for which jets receive a dedicated calibration of the jet mass, is also discussed.
|
ATLAS Collaboration(Aaboud, M. et al), Alvarez Piqueras, D., Aparisi Pozo, J. A., Bailey, A. J., Cabrera Urban, S., Castillo, F. L., et al. (2021). Measurement of the jet mass in high transverse momentum Z(-> b(b)over-bar)gamma production at root s=13 TeV using the ATLAS detector. Phys. Lett. B, 812, 135991–23pp.
Abstract: The integrated fiducial cross-section and unfolded differential jet mass spectrum of high transverse momentum Z -> b (b) over bar decays are measured in Z gamma events in proton-proton collisions at root s = 13 TeV. The data analysed were collected between 2015 and 2016 with the ATLAS detector at the Large Hadron Collider and correspond to an integrated luminosity of 36.1 fb(-1). Photons are required to have a transverse momentum p(T) > 175 GeV. The Z -> b (b) over bar decay is reconstructed using a jet with p(T) > 200 GeV, found with the anti-k(t) R = 1.0 jet algorithm, and groomed to remove soft and wide-angle radiation and to mitigate contributions from the underlying event and additional proton-proton collisions. Two different but related measurements are performed using two jet grooming definitions for reconstructing the Z -> b (b) over bar decay: trimming and soft drop. These algorithms differ in their experimental and phenomenological implications regarding jet mass reconstruction and theoretical precision. To identify Zbosons, b-tagged R = 0.2 track-jets matched to the groomed large-R calorimeter jet are used as a proxy for the b-quarks. The signal yield is determined from fits of the data-driven background templates to the different jet mass distributions for the two grooming methods. Integrated fiducial cross-sections and unfolded jet mass spectra for each grooming method are compared with leading-order theoretical predictions. The results are found to be in good agreement with Standard Model expectations within the current statistical and systematic uncertainties.
|
ATLAS Collaboration(Aad, G. et al), Alvarez Piqueras, D., Aparisi Pozo, J. A., Bailey, A. J., Cabrera Urban, S., Castillo, F. L., et al. (2020). Measurement of the ttbar production cross-section and lepton differential distributions in e mu dilepton events from pp collisions at root s=13 TeV with the ATLAS detector. Eur. Phys. J. C, 80(6), 528–70pp.
Abstract: The inclusive top quark pair (tt<overbar></mml:mover>) production cross-section sigma tt<overbar></mml:mover> has been measured in proton-proton collisions at <mml:msqrt>s</mml:msqrt>=13<mml:mspace width=“0.166667em”></mml:mspace>TeV, using 36.1 fb-1 of data collected in 2015-2016 by the ATLAS experiment at the LHC. Using events with an opposite-charge e μpair and b-tagged jets, the cross-section is measured to be: <disp-formula id=“Equ10”><mml:mtable><mml:mtr><mml:mtd columnalign=“right”>sigma tt<overbar></mml:mover>=826.4 +/- 3.6<mml:mspace width=“0.166667em”></mml:mspace>(stat)<mml:mspace width=“4pt”></mml:mspace>+/- 11.5<mml:mspace width=“0.166667em”></mml:mspace>(syst)<mml:mspace width=“4pt”></mml:mspace>+/- 15.7<mml:mspace width=“0.166667em”></mml:mspace>(lumi)<mml:mspace width=“4pt”></mml:mspace>+/- 1.9<mml:mspace width=“0.166667em”></mml:mspace>(beam)<mml:mspace width=“0.166667em”></mml:mspace>pb,</mml:mtd></mml:mtr></mml:mtable><graphic xmlns:xlink=“http://www.w3.org/1999/xlink” xlink:href=“1005220207907ArticleEqu10.gif” position=“anchor”></graphic></disp-formula>where the uncertainties reflect the limited size of the data sample, experimental and theoretical systematic effects, the integrated luminosity, and the LHC beam energy, giving a total uncertainty of 2.4%. The result is consistent with theoretical QCD calculations at next-to-next-to-leading order. It is used to determine the top quark pole mass via the dependence of the predicted cross-section on mtpole, giving mtpole=173.1-2.1+2.0<mml:mspace width=“0.166667em”></mml:mspace>GeV. It is also combined with measurements at <mml:msqrt>s</mml:msqrt><mml:mo>=7<mml:mspace width=“0.166667em”></mml:mspace>TeV and <mml:msqrt>s</mml:msqrt><mml:mo>=8<mml:mspace width=“0.166667em”></mml:mspace>TeV to derive ratios and double ratios of t<mml:mover accent=“true”>t<mml:mo stretchy=“false”><overbar></mml:mover> and Z cross-sections at different energies. The same event sample is used to measure absolute and normalised differential cross-sections as functions of single-lepton and dilepton kinematic variables, and the results are compared with predictions from various Monte Carlo event generators.
|
ATLAS Collaboration(Aaboud, M. et al), Alvarez Piqueras, D., Aparisi Pozo, J. A., Bailey, A. J., Barranco Navarro, L., Cabrera Urban, S., et al. (2019). Measurement of prompt photon production in root s(NN)=8.16 TeV p Pb collisions with ATLAS. Phys. Lett. B, 796, 230–252.
Abstract: The inclusive production rates of isolated, prompt photons in p Pb collisions at root s(NN) = 8.16 TeV are studied with the ATLAS detector at the Large Hadron Collider using a dataset with an integrated luminosity of 165 nb(-1) recorded in 2016. The cross-section and nuclear modification factor R-p pb are measured as a function of photon transverse energy from 20 GeV to 550 GeV and in three nucleon-nucleon centre-of-mass pseudorapidity regions, (-2.83, -2.02), (-1.84, 0.91), and (1.09, 1.90). The cross-section and R-p pb values are compared with the results of a next-to-leading-order perturbative QCD calculation, with and without nuclear parton distribution function modifications, and with expectations based on a model of the energy loss of partons prior to the hard scattering. The data disfavour a large amount of energy loss and provide new constraints on the parton densities in nuclei.
|
