Abstract: The excited structure of the single-hole nucleus 131 Sn populated by the beta – decay of 131 In was investigated in detail at the ISOLDE facility at CERN. This new experiment took advantage of isomeric purification capabilities provided by resonant ionization, making it possible to independently study the decay of each isomer for the first time. The position of the first-excited nu h 11 / 2 neutron-hole state was confirmed via an independent mass spectroscopy experiment performed at the Ion Guide Isotope Separator On-Line facility at the University of Jyv & auml;skyl & auml;. The level scheme of 131 Sn was notably expanded with the addition of 31 new gamma-ray transitions and 22 new excited levels. The gamma-emitting excited levels above the neutron separation energy in 131 Sn were investigated, revealing a large number of states, which in some cases decay by transitions to other neutron-unbound states. Our analysis showed the dependence between the population of these states in 131 Sn and the beta-decaying 131 In state feeding them. Profiting from the isomer selectivity, it was possible to estimate the direct beta feeding to the 3/2+ / 2 + ground and 11/2- / 2 – isomeric states, disentangling the contributions from the three indium parent states. This made possible to resolve the discrepancies in log ft for first-forbidden transitions observed in previous studies, and to determine the beta-delayed neutron decay probability (Pn) P n ) values of each indium isomers independently. The first measurement of subnanosecond lifetimes in 131 Sn was performed in this work. A short T 1 / 2 = 18(4)-ps value was measured for the 1/2+ / 2 + neutron single-hole 332-keV state, which indicates an enhanced l-forbidden M 1 behavior for the nu 3 s – 1 1/2 / 2 -> nu 3 d – 13 / 2 transition. The measured half-lives of high-energy states populated in the beta decay of the (21/2+) / 2 + ) second isomeric state ( 131 m 2 In) provided valuable information on transition rates, supporting the interpretation of these levels as core-excited states analogous to those observed in the doubly-magic 132 Sn.

Abstract: The International Linear Collider (ILC) will allow the precise study of e(-)e(+)-> q (q) over bar interactions at different center-of-mass energies from the Z-pole to 1 TeV. In this paper, we discuss the experimental prospects for measuring differential observables in e(-)e(+)-> b (b) over bar and e(-)e(+) -> c (c) over bar at the ILC baseline energies, 250 and 500 GeV. The study is based on full simulation and reconstruction of the International Large Detector (ILD) concept. Two gauge-Higgs unification models predicting new high-mass resonances beyond the Standard Model are discussed. These models predict sizable deviations of the forward-backward observables at the ILC running above the Z mass and with longitudinally polarized electron and positron beams. The ability of the ILC to probe these models via high-precision measurements of the forward-backward asymmetry is discussed. Alternative scenarios at other energies and beam polarization schemes are also discussed, extrapolating the estimated uncertainties from the two baseline scenarios.

Abstract: The large distances travelled by neutrinos emitted from the Sun and core -collapse supernovae together with the characteristic energy of such neutrinos provide ideal conditions to probe their lifetime, when the decay products evade detection. We investigate the prospects of probing invisible neutrino decay capitalising on the detection of solar and supernova neutrinos as well as the diffuse supernova neutrino background (DSNB) in the next -generation neutrino observatories Hyper-Kamiokande, DUNE, JUNO, DARWIN, and RES-NOVA. We find that future solar neutrino data will be sensitive to values of the lifetime -to -mass ratio tau 1 /m 1 and tau 2 /m 2 of O(10 – 1 -10 – 2 ) s/eV. From a core -collapse supernova explosion at 10 kpc, lifetime -to -mass ratios of the three mass eigenstates of O(10 5 ) s/eV could be tested. After 20 years of data taking, the DSNB would extend the sensitivity reach of tau 1 /m 1 to 10 8 s/eV. These results promise an improvement of about 6-15 orders of magnitude on the values of the decay parameters with respect to existing limits.

Abstract: The mass of the Higgs boson is measured in the H -> Z Z* -> 4l decay channel. The analysis uses proton-proton collision data from the Large Hadron Collider at a centre-of-mass energy of 13 TeV recorded by the ATLAS detector between 2015 and 2018, corresponding to an integrated luminosity of 139 fb(-1). The measured value of the Higgs boson mass is 124.99 0.18(stat.) +/- 0.04(syst.) GeV. In final states with muons, this measurement benefits from an improved momentum-scale calibration relative to that adopted in previous publications. The measurement also employs an analytic model that takes into account the invariant-mass resolution of the four-lepton system on a per-event basis and the output of a deep neural network discriminating signal from background events. This measurement is combined with the corresponding measurement using 7 and 8 TeV pp collision data, resulting in a Higgs boson mass of 124.94 +/- 0.17(stat.) +/- 0.03(syst.) GeV.

Abstract: The production of strip sensors for the ATLAS Inner Tracker (ITk) started in 2021. Since then, a Quality Assurance (QA) program has been carried out continuously, by using specific test structures, in parallel to the Quality Control (QC) inspection of the sensors. The QA program consists of monitoring sensor-specific characteristics and the technological process variability, before and after the irradiation with gammas, neutrons, and protons. After two years, half of the full production volume has been reached and we present an analysis of the parameters measured as part of the QA process. The main devices used for QA purposes are miniature strip sensors, monitor diodes, and the ATLAS test chip, which contains several test structures. Such devices are tested by several sites across the collaboration depending on the type of samples (non-irradiated components or irradiated with protons, neutrons, or gammas). The parameters extracted from the tests are then uploaded to a database and analyzed by Python scripts. These parameters are mainly examined through histograms and timeevolution plots to obtain parameter distributions, production trends, and meaningful parameter-to-parameter correlations. The purpose of this analysis is to identify possible deviations in the fabrication or the sensor quality, changes in the behavior of the test equipment at different test sites, or possible variability in the irradiation processes. The conclusions extracted from the QA program have allowed test optimization, establishment of control limits for the parameters, and a better understanding of device properties and fabrication trends. In addition, any abnormal results prompt immediate feedback to a vendor.