|
|
ATLAS Collaboration(Aad, G. et al), Amoros, G., Cabrera Urban, S., Castillo Gimenez, V., Costa, M. J., Ferrer, A., et al. (2012). Measurement of the top quark mass with the template method in the t(t)over-bar -> lepton plus jets channel using ATLAS data. Eur. Phys. J. C, 72(6), 2046–30pp.
Abstract: The top quark mass has been measured using the template method in the t (t) over bar -> lepton + jets channel based on data recorded in 2011 with the ATLAS detector at the LHC. The data were taken at a proton-proton centre-of-mass energy of root s = 7 TeV and correspond to an integrated luminosity of 1.04 fb(-1). The analyses in the e + jets and μ+ jets decay channels yield consistent results. The top quark mass is measured to be m(top) = 174.5 +/- 0.6(stat) +/- 2.3(syst) GeV.
|
|
|
|
ATLAS Collaboration(Aad, G. et al), Aparisi Pozo, J. A., Bailey, A. J., Cabrera Urban, S., Castillo, F. L., Castillo Gimenez, V., et al. (2020). Measurement of the t(t)over-bar production cross-section in the lepton plus jets channel at root s=13 TeV with the ATLAS experiment. Phys. Lett. B, 810, 135797–22pp.
Abstract: The top anti-top quark production cross-section is measured in the lepton+jets channel using proton-proton collision data at a centre-of-mass energy of root s = 13 TeV collected with the ATLAS detector at the LHC. The dataset corresponds to an integrated luminosity of 139 fb(-1). Events with exactly one charged lepton and four or more jets in the final state, with at least one jet containing b-hadrons, are used to determine the a production cross-section through a profile-likelihood t (t) over bar. The inclusive cross-section is measured to be alpha(inc) = 830 +/- 0.4 (stat.) +/- 36 (syst.) +/- 14 (lumi.) pb with a relative uncertainty of 4.6%. The result is consistent with theoretical calculations at next-to-next-to-leading order in perturbative QCD. The fiducial t (t) over bar cross-section within the experimental acceptance is also measured.
|
|
|
|
ATLAS Collaboration(Aad, G. et al), Amoros, G., Cabrera Urban, S., Castillo Gimenez, V., Costa, M. J., Escobar, C., et al. (2010). Readiness of the ATLAS Tile Calorimeter for LHC collisions. Eur. Phys. J. C, 70(4), 1193–1236.
Abstract: The Tile hadronic calorimeter of the ATLAS detector has undergone extensive testing in the experimental hall since its installation in late 2005. The readout, control and calibration systems have been fully operational since 2007 and the detector has successfully collected data from the LHC single beams in 2008 and first collisions in 2009. This paper gives an overview of the Tile Calorimeter performance as measured using random triggers, calibration data, data from cosmic ray muons and single beam data. The detector operation status, noise characteristics and performance of the calibration systems are presented, as well as the validation of the timing and energy calibration carried out with minimum ionising cosmic ray muons data. The calibration systems' precision is well below the design value of 1%. The determination of the global energy scale was performed with an uncertainty of 4%.
|
|
|
|
ATLAS Tile Calorimeter Community(Abdallah, J. et al), Castillo Gimenez, V., Costelo, J., Ferrer, A., Fullana, E., Gonzalez, V., et al. (2013). The optical instrumentation of the ATLAS Tile Calorimeter. J. Instrum., 8, P01005–21pp.
Abstract: The Tile Calorimeter, covering the central region of the ATLAS experiment up to pseudorapidities of +/-1.7, is a sampling device built with scintillating tiles that alternate with iron plates. The light is collected in wave-length shifting (WLS) fibers and is read out with photomultipliers. In the characteristic geometry of this calorimeter the tiles lie in planes perpendicular to the beams, resulting in a very simple and modular mechanical and optical layout. This paper focuses on the procedures applied in the optical instrumentation of the calorimeter, which involved the assembly of about 460,000 scintillator tiles and 550,000 WLS fibers. The outcome is a hadronic calorimeter that meets the ATLAS performance requirements, as shown in this paper.
|
|
|
|
ATLAS Collaboration(Aaboud, M. et al), Alvarez Piqueras, D., Bailey, A. J., Barranco Navarro, L., Cabrera Urban, S., Carrio Argos, F., et al. (2018). Operation and performance of the ATLAS Tile Calorimeter in Run 1. Eur. Phys. J. C, 78(12), 987–48pp.
Abstract: The Tile Calorimeter is the hadron calorimeter covering the central region of the ATLAS experiment at the Large Hadron Collider. Approximately 10,000 photomultipliers collect light from scintillating tiles acting as the active material sandwiched between slabs of steel absorber. This paper gives an overview of the calorimeter's performance during the years 2008-2012 using cosmic-ray muon events and proton-proton collision data at centre-of-mass energies of 7 and 8 TeV with a total integrated luminosity of nearly 30 fb(-1). The signal reconstruction methods, calibration systems as well as the detector operation status are presented. The energy and time calibration methods performed excellently, resulting in good stability of the calorimeter response under varying conditions during the LHC Run 1. Finally, the Tile Calorimeter response to isolated muons and hadrons as well as to jets from proton-proton collisions is presented. The results demonstrate excellent performance in accord with specifications mentioned in the Technical Design Report.
|
|
